A common problem with long-term use of the toilet is the loosening of fixation. The defect is minor, but it needs to be addressed quickly. This interferes with use and can lead to more serious damage. Maintenance companies know how to secure the toilet so it doesn't wobble. Just for a simple job, they ask for a solid amount. You can fix the toilet to the floor yourself. You just need to understand the cause of the malfunction and follow the instructions.
Why is the construction loose?
Before studying the instructions on how to fix the toilet so that it does not stagger, you need to understand what served this. There are 6 reasons:
- If the toilet sits on a wooden base, then the screws may have come loose.
- There are times when cracks form in the boards at the point of attachment to the floor.
- When laying concrete pavement, do notthe technological sequence was observed or the work was carried out with deviations from building codes. Subsequently, plumbing equipment will also have defects in fixation.
- Uneven floors will lead to similar problems.
- In old apartments, the floor was filled with concrete with the installation of a mortgage board. Over time, its strength decreases, the floor begins to "play", and the fixing bolts do not hold the toilet well.
- If the installation of the equipment was done in bad faith, and fasteners were used of poor quality, then problems are guaranteed in the future.
How to fix the toilet so that it does not stagger without resorting to the services of specialists? The first step is to determine the floor structure, and then follow the instructions below.
How to fix the toilet on a wooden base so that it does not stagger?
When it wobbles a little, just tighten the screws and the problem will be solved. If the fasteners are loosened significantly, do not try to tighten them. Otherwise, this will lead to cracks on the toilet body and will have to be completely replaced. It is necessary to purchase durable high-quality bolts so that the result of the work done is preserved for more than one year. The only possible option in the case of a wooden surface is to move the toilet. The whole process is carried out in 4 steps:
- holes need to be made in the wooden floor;
- unscrew the old mount;
- move the toilet to a new location andalign screw holes;
- screw the unit to the floor.
If it's a concrete floor
How to fix the toilet so that it does not stagger on uneven concrete? In the case of this basis, it will be more difficult to eliminate the problem of a “dancing” toilet bowl. First you need to completely dismantle it. This is done as follows:
- disconnect water supply hose;
- drain barrel being removed;
- sewer pipe disconnected;
- fasteners are unscrewed.
Then work is being done on the construction of a new foundation. The board is removed and replaced with a new one. In order for lumber to last longer, you can use special compounds. They will protect the board from swelling if liquid gets on it, as well as from rotting and fungus. How to fix the toilet on the cement, so as not to stagger? You can also just concrete the area and wait for it to dry. After completion of all floor preparation work, installation is carried out:
- The toilet must be installed on a new base and mark the attachment points with a marker.
- Using a puncher (in the case of a wooden board, a drill), drill holes at the marked points.
- Secure the unit with bolts.
- Mount the barrel.
- Reconnect sewer and water hoses.
How to fix the toilet so that it does not stagger on the tiles?
Even less reliable is the tile base. And since it is the most commonmaterial for flooring in bathrooms, then problems with a staggering toilet are not uncommon. The most radical solution would be to replace the old tile with a new one. But since this process is costly, you can try using special linings that have different thicknesses.
The easiest way to fix the toilet so that it does not wobble on the tile is to seal the gap with silicone sealant. For work you will need:
- sealant of the highest quality - the result of the work done depends on it;
- sealant gun - it is convenient for them to squeeze out the composition, and the layer will turn out even.
How the work is done:
- It is necessary to clean the surface of the floor from debris and dust, wipe the junction of the toilet bowl with the base with a cloth soaked in alcohol.
- Insert the gun into the tube of sealant, slowly walk along the contour of the plumbing fixture. Fill the gap between the floor and the toilet. If there is excess, have time to remove them with a scraper or a piece of cardboard until the composition is dry.
- Do not use the toilet for 4 hours. During this time, the sealant will seize and form a strong layer that will not allow the equipment to stagger.
