Modern washing machines are complex devices that have a range of additional functions and modes designed to perform versatile tasks to make the work of their owners easier. At the same time, this technique has a lot of protective systems that protect it from damage or violations in the technical process. With this in mind, even the smallest breakdown can cause difficulties for the user in operation and usually leads to the call of the master, which is directly related to additional costs. However, if the washing machine does not draw water, then sometimes it is enough to perform certain actions or carry out independent repairs in order to save money and not contact the service center for trifles.
Types of breakdowns and their elimination
To begin with, it’s worth saying right away that all the methods below are suitable for almost all models of such equipment. These are the simplest manipulations that can be done independently, without disassembling the unit and without special education. When the washing machine does not draw water and everything described below did not help fix the problem, then you should contact the servicecenter.
No water in system
This reason is commonplace, but first of all it is worth checking it. The fact is that many housewives are sometimes so passionate about household chores that they sometimes forget that this product needs to be replenished from the water supply system. Therefore, if the washing machine does not draw water, then try to open the tap and make sure that you have it in your apartment. This behavior of the device is also possible with a small pressure.
Fan turned off
Very often, when connecting such devices to the water supply, a special tap is installed that blocks the access of liquid to the unit. Sometimes it is practically not used and its presence is simply forgotten. As a result, if you block it, you can not immediately guess the reason for this behavior of the device. Therefore, if the washing machine does not draw water, then it is worth checking this locking mechanism and, if necessary, moving it to the open position.
Violation in progress
Sometimes this technique very often behaves strangely if a mistake has been made in the program. When the washing machine draws in and drains water before the start of the wash, then this may refer to this type of mismatch. What to do:
- First of all, you should pay attention to the presence of laundry in the drum. Some models, in its absence, may either not draw liquid at all, or immediately drain it.
- Sometimes such a defect occurs already in the washing process itself, which is usually associated with a large weight of the laundry itselfor uneven distribution. Modern technology is equipped with just a huge number of sensors that control the entire process.
- Some models control the closing of the loading door and even the tray into which the powder is poured. Therefore, it is worth checking the tightness of their fit to the body.
Such violations in the process usually have their own error code and are often displayed on the operating display of the device. Some manufacturers give a decoding of these signals in the instruction manual.
Door breakage
If the washing machine does not take on water, the reasons for this behavior are most often associated with a malfunction of the door. The fact is that a special sensor is installed on its lock, and if it does not work correctly or is out of order, then there will be no fluid supply. It is worth noting that replacing such a part is quite simple, and in some models it can be done without disassembling the device. Very often, users simply remove the sensor itself, closing its contacts, but then the lock stops holding the door, which can lead to its spontaneous opening during the spin process, when vibration increases.
Clogged filter
If you are wondering why the washing machine does not take on water, it is worth considering certain design features of the model. The fact is that at the entrance to the supply system of the device, a small filter in the form of a metal filter is often installed.grids. It needs to be cleaned periodically:
- First, disconnect the hose of the machine from the water supply. A wrench may be required for this as the hose is connected through a special coupling.
- On one of the ends of the connection pipe, such a filter is usually installed. It needs to be cleaned.
- In some cases, the metal mesh rusts and completely fails. In this case, it must be replaced.
- At the end of the work, assemble the system back by connecting the hose to the water supply.
Intake valve failure
If the Indesit washing machine does not draw water, then sometimes the reason is a malfunction of the special inlet valve, which is located at the inlet to the device. A similar defect is characteristic of units from other manufacturers, since this element is common to all products of this type. At the same time, it should be noted that its design is made in such a way that when it fails, it switches to the "locked" position to prevent flooding.
It is quite difficult to fix such a breakdown on your own. To do this, you will have to disassemble the device, disconnect this unit from the water supply system and disconnect the controller contacts from it. After that, the valve is removed and replaced. The elimination of such a malfunction can be attributed to minor repairs, although its cost directly depends on the price of the required part.
Pump failure
Only a master can diagnose such a malfunction. However, if the tank itself is full, there is no pumping out and no water enters, then this is the first sign of such a malfunction. In this case, you should first check the filter of the device, because if it is clogged, then the liquid cannot be drained. If the cleaning did not bring results, you need to contact the service center.
Replacing this assembly can be quite expensive, so you should be very careful with the product during operation. It is necessary to periodically clean the filter and install the drain hose at the level recommended by the instructions.
Faulty programmer
Modern household appliances for this purpose are equipped with rather sophisticated electronics that control the entire process. Therefore, if it fails or fails, then the washing machine simply does not draw water. What to do in such cases is usually indicated in the operating instructions for a particular model. However, there are also the simplest actions that you can do yourself:
- First of all, a breakdown of this type is displayed on the display of the device. It may look like an error, an incorrect inscription, or a complete lack of indication. This is how this defect is defined.
- Next, you need to disconnect the device from the power supply and leave it in this position for 10-15 minutes. After that, they turn on.
- If after such actions the machine does not work, it is recommended to call the wizard. It is quite difficult to repair such a mechanism on your own, especially if there is no special tool, no appropriate education and spare parts.
Problems in the pressure sensor
This node is designed to control the water supply to the machine. It is he who is responsible for the amount of liquid in accordance with the weight of the laundry. Therefore, if a breakdown occurs in it, then water simply will not flow into the device. Replacement of this part is carried out with the help of service center specialists, where it is almost always available.
It is better not to carry out such repairs on your own. The fact is that in some models it is necessary to make subsequent adjustments or adjustments, and for this you need to have the appropriate equipment.
Recommendations from experts
- If the washing machine draws water and immediately drains it, then you should pay attention to the washing mode that is set on the programmer. Quite often, housewives simply forget that they have chosen a certain way of performing a task, which implies such behavior. That is why experts recommend testing in the optimal mode.
- If the product is under warranty, then you should not disassemble it yourself and replace certain components. Calling a qualified specialist will take some time, but will save a significant amount.
- Sometimes the instruction manual describes in detailsequence of actions in case of detection of a certain breakdown. All instructions should be followed clearly and in the given order, since they are written for a specific model, taking into account its technical features and test tests.
- If the device hose is disconnected from the water supply system, then it is necessary to shut off the fluid supply in this area or completely in the network.
- On some models, the operation of the inlet valve is checked by turning on the machine in the network. If this assembly is OK, then a characteristic click should be heard, caused by the temporary opening of the valve.
Conclusion
If the washing machine does not draw water, then there can be many reasons for this behavior in this device. That is why, before contacting specialists, it is necessary to completely exclude the influence of the human factor so as not to spend money on repairs and not look stupid in front of the master who discovered that you simply turned off the inlet valve. At the same time, most of the breakdowns associated with such a malfunction can be eliminated on your own without disassembling the machine.
