In stores today there are different lampshades for the chandelier. With your own hands, however, such products can be made quite simply. As a result, it will be possible to get a very original solution that cannot be found in any other interior.
Making a lampshade from cardboard
To carry out the work you will need thin white cardboard, a glue gun, fishing line or thin twine, a clerical knife that can be replaced with scissors, round nose pliers, and wire for the frame.
Features of the work
DIY chandelier lampshades can be made quite simply. To do this, you need to prepare all of the above materials and tools. After the master will have to decide on the dimensions of the product. The example will consider a diameter within 30 cm. This indicates that for manipulation it is necessary to prepare cardboard, the length of which is 90 cm.
First you need to make a frame for which a piece of wire is cut off. Lastit is necessary to give a length within 98 cm. From this workpiece, roll a circle with a diameter of 30 cm, fixing the ends with round-nose pliers. Next, 3 hanging elements are cut from fishing line or twine. The length of the pieces should be measured taking into account the height at which the lamp is supposed to be hung.
Three elements prepared in advance should be tied with wire in three places. When fixing, the elements are distributed evenly. If you make lampshades for a chandelier with your own hands using the described technology, then on the cardboard at the next stage you need to depict butterflies of different sizes, and then cut them out. Now the cardboard is rolled up in the form of a cylinder, the joint is glued with thick paper or stitched with a stapler. The upper part of the plafond must be fixed on the wire. For this, it is recommended to use a piece of thin wire or glue.
Final works
When lampshades for a chandelier are made by hand, it is important to follow the technology of work. Only in this way will you be able to achieve a positive result. If the joints and cuts turned out to be not too aesthetic, then you can decorate them with butterflies. Such a lamp can be used both in the children's room and in the bedroom. Instead of butterflies, you can cut out flowers, snowflakes or stars - in general, whatever comes to your mind.
Back to the USSR
If you are thinking about how to make a lampshade for a chandelier with your own hands, then you canplunge into the memories of the sixties. In those days, floor lamps were especially popular, which were made in the form of a cylinder. To carry out such work, you will need a decorative braid, a crochet hook and scissors. When choosing the first element, you need to combine colors to your liking.
Work technology
Before you make a lampshade for a chandelier with your own hands, it is recommended to make a sketch. After that, you can start working. To do this, you need a frame that can be borrowed from an old lamp; the first braid should be tied to its lower part. The tail should have a length of 5 cm. The braid should be pulled over the upper ring from the outside, thrown over and stretched through the lower ring, or rather, its inner side. These actions should be alternated until the next frame sector begins.
If you make a lampshade with your own hands for a chandelier, then the braid in the next step should be fixed. Next comes the braid of a different color. It should be knitted to the next sector, not forgetting to leave a tail. The third sector is filled in the same way with the remaining braid. The ponytails should be stretched from below with a crochet hook. On this, we can assume that the ceiling from the 60s is ready.
Fringe and lace lampshade
If you decide to make a lampshade with your own hands for a chandelier, then in the process of work you can use fringe, which will form the basisquite an interesting idea. Before starting work, you need to prepare two steel hoops or use an embroidery hoop. The craftsman will need fishing line, a glue gun, fringed braid and acrylic paint. It must match the color of the ribbon. You will also need scissors.
Production method
Before you make a lampshade for a lamp with your own hands, the hoops or existing hoops must be painted with acrylic paint. While the composition dries, it is necessary to make 3 marks on the rings, placing them at the same distance from each other. Now you need to cut three pieces of fishing line. They need to be tied to a smaller ring, leaving the upper ends with a margin, so as to tie the lamps later.
Now the master must determine the length of the fringe, subtracting 2 cm from it. Tie the fishing line to the second end for the resulting length. This will give you a cascade. Now comes the turn of the glue gun, with it you will need to fix the bottom ring. The same manipulations must be done with the upper ring.
It is important to consider that the line can melt when exposed to glue, so it must be applied in such a way that the materials do not interact while the composition remains hot. Glue for this is applied to paper, a certain time is waited, only after that you can start fixing.
Alternative solutions for lampshades
If you want to make a lampshade for a chandelier with your own hands from fabric, then you can use one of the above technologies. This is especially true for the last option, whenthe fabric is adjusted to a pre-prepared strip, and then cut in such a way that it is possible to obtain strips hanging down. However, it is not necessary to start work from scratch if you want to create a beautiful lampshade. For example, you can use a paper lantern, supplementing it with forms from chocolate platter or cupcakes. The latter are glued to the base of the lantern, allowing for a new lampshade design.
Conclusion
If you decide to make a lampshade with your own hands for a chandelier from threads, then you can use, again, the above technology. The threads are sewn onto a pre-prepared strip, the length of which corresponds to the size of the hoop. Threads can be different in color and length, which allows you to get an unsurpassed effect.
For work, a paper ceiling can also be used, which is complemented by pendants. Glass jars can also become part of the lampshade. To do this, they are painted with paints, and, if possible, decorated with engraving. If one of the rooms in your house has a high-tech style, then you can use tin cans that you don’t even have to paint.
