The angle grinder is a tool that has a rather obstinate character. With the help of this equipment, you can grind, cut and clean surfaces, however, the unit operates at high speeds, and it is sometimes quite difficult to hold it in your hands. As a result, high accuracy cannot be expected. An angle grinder stand is perfect for solving such a problem; you can make it with your own hands quite simply.
For this, craftsmen usually use metal, but some have learned to adapt even wood, because it is easy to process and affordable. Practice shows that such a solution turns out to be very short-lived, but it is great for those who do not use the grinder so often.
Isn't it easier to buy
The grinder stand has recently become a great helper for professionals and home craftsmen who are used to working with an angle grinder. The device is very convenient, and if you have to operate the equipment often, then whenIf necessary, you can purchase an additional tool so that each time you do not waste time installing it on the rack. If this approach is unacceptable for you, then you can make a stand yourself.
In addition, Chinese-made models are not ready to last as long as we would like. They are made from sheet metal using stamping technology. The vibration of the tool leads to the fact that light parts scatter from vibration, and the design itself has a small weight, and also has a low level of stability. Purchasing an expensive rack option can be expensive. If you are not considering this approach, then it is better to make a fixture for installing the angle grinder yourself.
Which material to choose for making a tripod
If you are going to make a stand for an angle grinder with your own hands, then it is important to think about what material to use for the work. The most commonly used profiled metal pipes. This material is the most reliable and strong, which is why it is so popular.
However, there may be some problems that the master will have to use the technology of electric welding. Equipment for this at hand may simply not be found. However, almost all welding work can be replaced by the use of strong bolts that are installed in pre-drilled holes. This option is the best approach, because in this case it will be possible to disassemble the machine.
What you need to make a rack
Quite often, recently, home craftsmen have been making a rack for angle grinders with their own hands. If you decide to use profiled pipes in your work, then you should cut blanks from them and drill holes. Before cutting the pipes, it is important to clarify the dimensions so as not to spoil the expensive material.
You can also use wood in your work, in which case the rack can be made with less labor costs. But the process may have some difficulties, expressed in the poor quality of the components and the wear of the material. Therefore, it is recommended to use quality lumber that does not warp.
Preparation of tools and materials
If you will make a stand for angle grinders with your own hands, then you should take care of the availability of tools and materials, such as:
- bolt;
- screw;
- nut;
- drill;
- pliers;
- screwdrivers;
- metal sheet;
- grinding wheel;
- set of keys;
- self-tapping screws;
- welding machine;
- drilling machine;
- angle;
- milling cutter;
- puck.
Design features
Before starting work, you must determine what nodes the structure will have. It may have a bed, which isa metal or wooden plate in the form of a frame. Sometimes the system is complemented by a carriage for material and tools. If desired, you can install the transfer unit on rollers. If you want the grinder or material to move at a certain angle, then tilt nodes should be provided.
Making the simplest model
You can make a stand for angle grinders with your own hands, it is recommended to consider a photo of these designs in advance. They are provided in the article. The simplest solution would be a holder, which is made of metal and textolite. You can only use the first version of the material. It is better not to use wood in this case, as it will not be able to withstand the load.
The device will look like plates that are fastened together by screws or welding. The latest technology can be used if only metal is used in the work. Bolts must be used when the design assumes the presence of textolite. One of the plates will serve as a mobile platform; it can be made from a 3 mm steel sheet or duralumin. This item must measure 35 x 15 cm.
As an alternative solution, you can use textolite, but in this case, you should use a 6-mm blank. If you are doing a stand for an angle grinder with your own hands, then the second plate will act as a stop. It is made from a 4 mm piece of steel, the dimensions of which are 125 x 50 mm. This node will havethe main load, so it is not recommended to use thin metal. Otherwise, the rack may be unsafe.
On one half of the plate, several holes should be made using a drill with a diameter of 4.5 mm. This will allow you to commit to the platform. An 8 mm hole should be made in the central part of the second half. Holes are made in the platform and drilled from the back to install countersunk screws. Instead of the second plate, you can use a 4mm angle by drilling it accordingly.
The corner or plate is screwed and welded to the platform so that the cutting disc is 5 mm away from the edge of the bed. When making a stand for an angle grinder 230 with your own hands, the corner must be bent in relation to the frame by 60 ° C. The cutting power tool must be fixed on the upper part with a bolt with a lock nut, this will prevent the bolt from turning and vibration during work. On this, we can assume that the device is ready.
Addition of the rack with knots
In order to ensure increased cutting accuracy and facilitate work, the fixture should be supplemented with metal squares and wooden blocks, their dimensions should be as follows:
- 30 x 30 x 420mm;
- 27 x 30 x 35mm;
- 55 x 30 x 80mm;
- 120 x 60 x 25 mm.
From the end of the longest square, you need to measure 12 cm and bend the workpiece in the shape of the letter "L". This element and the main platform should be drilledholes to be drilled for countersunk screws. The plate and the square at the next stage are connected, the bars are superimposed on top, and then the structure should be screwed on. In order to facilitate the work, you need to install an additional handle.
Another rack knot
When a do-it-yourself stand for angle grinder 125 is made, it can be supplemented with one more node. For this, a universal limiter is used in the form of a guide, which is made of metal strips, their width can vary from 75 to 100 cm. There should be two such blanks.
You will need a square, its length can be equal to the limit from 30 to 70 cm. Borrowing roller nodes from door drawers in the amount of 2 pieces, you should supplement the rack with these nodes. Assembly is carried out according to the following technology. Guides are fixed on the platform, and two strips are screwed on top. Their ends should be equally spaced from each other. A square is fixed at the ends of the strips so that it bends down. When a home-made rack for an angle grinder (angle grinder) is made with your own hands, clamps or a screw clamp are used to fasten the roller assemblies. It should consist of an 8 mm plate, the length of which is equal to the main platform. Whereas the width can be equal to the limit of 5 to 8 cm.
Conclusion
An angle grinder has recently become quite a popular household tool. It is an indispensable tool for installation, repair and construction work. Can be used to cut stones and metalother structural metals. But it can be quite difficult to operate such equipment, because its working parts move at great speed. You can make a stand for an angle grinder with your own hands, you can find drawings of such structures in the article. Such a device allows you to ensure accurate cutting and reduce vibration.
