In the process of repair, people are constantly polluted with paints, building dust, chalk, and other means. But they are well washed off, but other materials, such as construction foam, are very difficult to remove from skin or clothing. It is important to know how to clean mounting foam from hands and skin in general in order to avoid discomfort, injury and poisoning by the chemical composition of the substance. There are several optimal options that have been tested by builders and recommended by foam manufacturers.
Foam Handling Precautions: Wear Protective Clothing
In order not to think about how to clean the mounting foam from your hands, you should follow the rules regarding protection in the process of working with the material:
- Goggles and high-lapeled gloves must be worn.
- Clothes are selected specifically for one-time use with foam, as the composition is not washed.
- When working, a headdress must be present on the head.
- For additional protection of yourself and surrounding objects, it is advisable to use a piece of film.
Even if you completely protect your skin and hands from foam, problems may arise. It is better to purchase a special tool for removing building material.
When is it easy to clean the foam from hands
When mounting foam gets on your hands, it will be much easier and faster to remove it in such situations:
- In the first few minutes after getting the product on your hands, the foam can be easily washed off with warm water with the addition of any soapy product.
- In the first minute, you can remove dirt with a rag, just wipe the flakes thoroughly.
- If you first apply a greasy cream or lotion to the skin, then it will be much easier to remove pollution even after work is completed.
In many ways, the quality of cleaning depends on the composition and characteristics of the foam itself. High quality outdoor building material cannot be removed in any of the above situations.
Dedicated foam remover available in the store
The modern construction market offers a huge variety of sealants, installation tools. In this regard, there was a need for special products that can neutralize this substance.
This is the polyurethane foam cleaner, which has a strong effect. Such a solvent is used to remove sealants of various effects. You can buy the product paired with foam.
Recommendationsprofessionals are as follows: building material and solvent must be of the same company. One manufacturer guarantees quality impact on pollution.
Solvents of this type are often made in the form of an aerosol. This greatly simplifies the process of applying the substance to the hands and improves the impact. The cleaning procedure is carried out in a matter of minutes and guarantees a positive result.
An analogue of the solvent can be a liquid for removing cosmetic varnish. It is necessary to apply the liquid on a cotton pad and wipe the foam from the skin of the hands with light movements. The remedy is considered to be especially effective in the first few minutes after contamination.
Folk methods for cleaning hands from building material
There are folk methods for cleaning the skin of hands and other parts of the body from foam and sealant. Such products are considered more gentle on the skin, but do not particularly differ in effectiveness. Another advantage of folk inventions is the low price.
How to wash your hands after polyurethane foam using folk remedies and recommendations:
- Heat vegetable oil to 30 degrees and apply to problem areas. After rubbing your hands well together, wash off the remaining composition with a large amount of warm water. It is advisable to use soap or dishwashing detergent during the washing process.
- Washing hands with combustible substances such as gasoline or kerosene, sometimes diesel fuel, will be the standard option. The next step is to wash your hands with soap and water. The gun is washed with the same means forapplying polyurethane foam.
- S alt or sand can be good cleaners for hand skin from polyurethane foam. You need to take a handful of bulk material and wet it a little. Rub hands for several minutes and then rinse with plenty of water.
Foam cleaner, according to popular recommendations, can be several options at the same time. The faster the remedy is applied, the better the result.
Mechanical removal of any type of contamination with sealant or foam
If there is no way to clean the mounting foam from your hands, or you can’t clean it with means, you need to use a mechanical method. It is worth choosing the most gentle way that does not harm the skin.
How to clean hands from polyurethane foam using a mechanical method? There are several options for action:
- Apply a fat cream for hands, body or face to the mass. The layer of cream should be dense enough so that the surface is well saturated with the composition.
- Soak a pumice stone for feet in hot water and apply soap on the surface. It is advisable to use a liquid soap that has a more delicate texture.
- Rub the foam with a pumice stone, achieving the desired effect. Movement should be light and fluid so as not to cause pain.
- If you experience pain, you should stop the action. Pain indicates that the epidermis is affected.
- Wash your hands with soap. Then rinse your hands again in warm water.
- Apply hand cream. Wait a few minutes until the composition is partially absorbed into the skin.
Instead of pumice, you can use acrylic or gel nail files. Heel grinders are fine too. The main thing is not to overdo it with mechanical impact, so as not to get injured.
Removing dried foam from hands using proven methods
Cleaning hands from fresh drops of foam is easy, but old stains are difficult to remove. Before you clean your hands from dried mounting foam, you will have to try more than one tool and method. At the same time, you will have to live with a foreign mass on the skin for about 3-5 days, until the skin is renewed and the “construction dirt” disappears by itself.
First, you need to break off as close to the skin as possible, cut off drops of hardened foam. After that, s alt or sand is used to remove excess particles of the building mass to the maximum. After that, you can use a solvent that will further clean the surface of the skin.
The penultimate step will be washing your hands with plenty of water and detergent. The last point is the use of a nourishing cream to restore the microflora on the surface of the epidermis.
What methods are not recommended for pollution control
In search of options on how to get rid of mounting foam on their hands, many find completely barbaric methods. It is worth thinking not only about the result of cleaning the skin, but also about maintaining its integrity.
Do not use mechanical methods to remove foam from hands. ATin particular, do not use metal, hard brushes; metal brushes; knives and other cutting objects. Such exposure can lead to skin damage, deep wounds.
Another popular method is the use of acids and harsh chemicals. But it is almost impossible to predict the behavior of chemicals. As a result, deep and extensive skin lesions, poisoning, and respiratory problems can occur.
Useful tips and advice from professionals
After you have decided how to clean the mounting foam from your hands, it is worth considering other nuances regarding cleaning. Builders give the following recommendations and advice:
- Be sure to use hand cream at various stages in the process of any cleaning. This will greatly improve the condition of the skin.
- It is undesirable to use vinegar to clean hands from mounting foam. Acid can significantly damage the skin.
- Better to pre-protect: rub your hands with cream, put on gloves, use a special device for applying foam.
If there is a lot of free time, then thin films of dried foam residue can be removed with tweezers. This option is ideal if the areas are small and do not have severe skin lesions.