In the process of construction and repair work, mounting foam is often used. This material is distinguished by its strong fixation. If such material accidentally gets on hands or clothes, it will be extremely difficult to remove it, but it is quite possible.
Special tools are used for this. If such a nuisance occurred during the repair work, effective ways to remove material from different surfaces should be considered. How to wash mounting foam will be discussed later.
Foam Features
Many people believe that things soiled with such material are easier to throw away than to wash with polyurethane foam. However, what if this material gets on furniture, hands or hair? This is where you need to act fast.
Such a strong fixation of the foam is due to its purpose. This is a polyurethane sealant. With it, you can blow out various potholes, cracks and connect certain types of materials. Previously, instead of mounting foam, they usedsolution with tow. Modern materials have a lot of advantages. So, working with polyurethane foam does not cause difficulties even for a beginner. This material is quickly applied to the surface.
Also, the foam quickly hardens, turning into a monolithic layer of polyurethane. Getting on the skin, this material completely blocks the access of oxygen to the epithelial cells. This adversely affects his condition. Therefore, polyurethane foam must be urgently washed off. Otherwise, irritation may occur throughout the body, an allergic reaction.
What do you need to do before starting work?
So that later you don’t have to decide how to wash the mounting foam, you need to properly prepare for the process of working with the sealant. Nearby items need to be moved to another room. If the furniture is large, it must be covered with a cloth. This will prevent accidental contact with polyurethane foam on the surface of sofas, armchairs, cabinets, etc.
You need to prepare clothes that, if necessary, can simply be thrown away. Sleeves in such overalls should be long. It is best if they have tight cuffs. Pants should also be long. The number of exposed skin areas should be reduced. Hands, face, legs and other parts of the body must be covered with clothing.
It is highly recommended not to work with sealant without goggles. It will be almost impossible to wash off such a composition from the eyes on your own. You will need to go to the hospital. Therefore, the use of special building glasses iscompulsory. Gloves must be worn on hands. Such preparation will significantly reduce the risk of polyurethane foam getting on the skin or interior items.
Special tool
Considering how to wash mounting foam from hands, a few words should be said about special washes. Such formulations are sold in the form of aerosols or creams. They are used to clean tools used in blowing foam. They can be used to remove traces of sealant on hands.
Sprays are less toxic than ointments. However, they must be used very carefully. First you need to spray the composition on the contaminated area of \u200b\u200bthe skin. Then you will need to wash off the composition with plenty of warm water. Such a remedy only helps if the foam has not yet hardened.
It happens that the master did not have time to take timely action when the sealant gets on the skin. In this case, the foam quickly hardens. Aerosol in this case will be powerless. In this case, you can use a special cream. It is toxic and can cause allergies. However, if hands and hair are heavily contaminated with sealant that has cured, this is perhaps the only way to wash off polyurethane foam.
What should I do if foam gets on my skin?
When studying how to wash mounting foam from your hands, you should consider the recommendations of experts on the actions of the master in such a situation. If sealant gets on the skin, you should immediately take a cloth napkin. With its help, the foam stain must be carefully wiped off. The movement is carried out to its center. Otherwisepolyurethane foam will be smeared on the hands. Washing it off in this case will be much more difficult.
Next, you need to use any suitable tool at hand. If there is no special aerosol, you can use alcohol, gasoline, acetone. The listed compounds are used in an identical way.
Before the foam has hardened, you need to take a tissue napkin or cotton wool. A sufficient amount of acetone or other similar substance is poured onto them. Then the napkin is applied to the skin. Rub gently. Do not smear contamination over the entire surface of the hands. After treatment, the skin is washed off with warm running water.
Folk recipes
You can wash your hands from polyurethane foam at home using simple recipes. They have been tried by many masters and have been able to prove their effectiveness.
One of the easiest and most effective ways is to use vegetable oil. It needs to be warmed up a bit. Then a napkin is moistened in oil and the hardened foam is rubbed off. After half an hour, your hands will be clean. At the same time, the skin will look well-groomed, since the oil, unlike acetone, does not harm it at all.
You can also use regular kitchen s alt. This is an abrasive substance that will help to mechanically remove the remaining foam. You need to pour s alt on a napkin and rub the contaminated area. This method will require patience and a lot of time, especially if the foam has hardened. However, s altwill help to completely remove the sealant from the epithelium. After the procedure, the hands are thoroughly washed and treated with a nourishing cream.
Removing cured foam from hands
There are several ways to wash the hardened polyurethane foam. Not always the master can quickly notice that the sealant has got on his hands. In this case, it will take much more time and effort to remove the pollution. The solvents listed above will be powerless in this case.
To remove the hardened sealant, you will need to prepare a hard brush, pumice stone. Fine grit sandpaper may also work. You should also prepare a greasy cream and soap. Rinse off the foam very carefully. If you apply too much force, you can significantly damage the skin. Abrasions and wounds will appear on it.
It is necessary to treat the contaminated areas with a greasy cream. So the brush will scratch the skin less. Next, the brush, pumice stone or other selected abrasive material must be heavily lathered. Before the procedure, it is recommended to steam the hands for 10 minutes. in hot water. So the foam will be removed faster. With a brush, carefully treat the surface of the contamination, trying to minimize its impact on clean areas.
How to remove foam from clothes with improvised means?
If the sealant got on the clothes, many craftsmen are looking for a simple remedy than to wash the mounting foam at home. You need to act quickly. First, the bulk of the polyurethane foam is removed with a spatula from the fabric.
Next, you need to impregnate the material with a solvent, acetone or gasoline. If the foam has not yet hardened, traces of dirt can be removed quickly and without much effort. In this case, the fabric will remain intact. It will need to be washed in plenty of water. It will take a large amount of powder to wash off the smell of the solvent. Can also be machine washed.
You can also use white spirit, if such a composition is at hand. If the clothes have a pattern, all of the above products can lead to discoloration. Therefore, solvents and other active liquids should be used very carefully. It is better to test the effect of the product on an inconspicuous area. You can also use alcohol. It has less effect on the material than other compounds.
How to remove foam from floors and furniture?
You can also consider a few tips on how to clean mounting foam from furniture or floors. If by accident the cylinder fell, staining the door, floor or interior items, you can correct the situation using simple methods.
If the surface filled with sealant is not susceptible to mechanical stress, you can remove the foam with a knife or spatula. These tools remove the hardened layer of polyurethane.
If the sealant got on the polished surface, this method is absolutely not suitable. In this case, you can use Dimexide. This drug is sold in pharmacies. The medicine has a sharp, unpleasant odor. When using it, you need to protect your hands with gloves.
Before the foam has hardened, it must be washed offpaper towel, being careful not to smear the stain. Next, on the polished surface, you need to put a cloth soaked in Dimexide. The material should remain on the foam spot for about 20 minutes. Then the fabric is removed. After that, with a sponge with a hard pile, you need to quickly remove the pollution. Special tools for cleaning construction tools will also be effective. For example, it could be Reiniger, Cosmofen.
A few tips
Experienced installers give some tips on how to wash mounting foam from clothes. They claim that material that has come into contact with sealant will be easy to clean if put in the freezer for a few days. From changes in temperature, the foam is deformed. After the freezer, clothes can be put in boiling water if the structure of the fabric allows it. This will enhance the effect.
Having considered how to wash mounting foam, you can quickly remove traces of dirt from leather, fabric and interior items with the help of available tools.
