You can drag the chair with any material, depending on the taste preferences of the client, interior design or financial capabilities. This can be leather, its substitute or other textile analogue.
Tightening components
Do-it-yourself office chair upholstery most often occurs with the following types of materials:
- Genuine leather. It is considered the most elite and prestigious option. It should be handled carefully. The work will require additional tools, which will also increase the cost of repairs.
- Leatherette. The best option for the price category, but also the most short-lived. This office chair upholstery, although cheap, will last no more than 2 years, which is less than that of inexpensive fabric upholstery. There are high quality leather substitutes that are in no way inferior to genuine leather, but their cost is almost equal.
- Textile. This material has the widest range in both color and fabric texture. A cheap option is chenille - this is a fabric,made of cotton and synthetic fibres. Next in ascending order: flock, jacquard, microfiber and tapestry.
Repair features
The design of the chair and its material are determined by what it is intended for. This may be the chair of the boss or management, or an ordinary employee or client. The upholstery speaks about the status of the chair. Often this is a leather version. Others have cheaper analogues or a textile surface - they are lighter in design and mobile.
When the chair is already very fond of the owner, it is not necessary to buy a new one and get used to it. You can have old furniture upholstered or do it yourself if skills, materials and tools allow.
Steps of work
Do-it-yourself upholstery of an office chair is not as difficult as it might seem at first. It is not necessary to call the master if you have the right tools and materials at hand. For work, you will need the following elements: fabric for sheathing, foam rubber, scissors or a knife, screwdrivers - Phillips and flat, furniture stapler.
Before starting work, the chair will have to be disassembled. It is easier to do this if there is an instruction. But often there is none, so you need to deal with the device and properly disconnect the cover and seat. It is better to take a picture of the chair before the start of the disassembly and at the next stages, because it will be easier to assemble it after the repair.
A simple product has a standardfasteners, so hauling an office chair with your own hands will not take much time. It is enough to unscrew the bolts and screws in certain places. When the parts of the chair are disassembled, you can begin to remove the old upholstery. To do this, use pliers, a screwdriver and an anti-stapler, if there are staples. After that, according to the standards of the old skin, we make patterns on the new material. To do this, simply attach the products to each other and circle the contour.
Next, lay the material on the floor in this order: sheathing component, foam rubber and frame (back or seat). Then it is good to fasten the first one to the frame, while pulling it well - do not make folds, but carefully fix the result with a stapler. Upholstery of an office chair with leather is not only giving an updated look to furniture, but also raising the status of an organization, especially in the eyes of customers. When both parts are sheathed, you can put the chair back together and enjoy the work done.
How to reupholster a chair with Alcantara?
Material such as Alcantara is widely used in various fields. This is an artificial suede that has a sticky layer underneath. Thanks to this, it fits perfectly on the surface. Alcantara has a good service life (up to 7 years), it is not very stretchable, but elastic enough to make it comfortable to work with. The best Alcantara is made in Korea, it should have a 5 x 5 cm lined grid on the back.
You can drag a Chinese-made chair using the following devices: pliers, marker, tapecentimeter, scissors, ruler, knife, directly alcantara with self-adhesive.
To prevent overspending of material, it is necessary to make a calculation. To do this, measure all parts of the chair. Next, add 5 cm to each side for allowances. The excess is then cut off with a clerical knife. After that, you can disassemble the chair by simply unscrewing the necessary elements. Then cut off the necessary pieces of Alcantara, while marking the dimensions with a marker on the inside.
Should I remove the old upholstery?
Upholstering an office chair with Alcantara suggests the possibility of not removing the old upholstery. Alcantara is such a comfortable material that it fits on any surface. The protective base should be separated from the piece and attached to the workpiece, while Alcantara should be leveled so that there are no wrinkles. Wrap the excess around the edges. Later they are fixed or trimmed. At the same time, you need to cut off immediately, otherwise it will be impossible to peel off the Alcantara in an hour.
Upholstery of the whole chair or part?
Often, users are dissatisfied with only a separate part of the chair, while it is possible to replace only the back or seat upholstery. The scope of work must be established before they begin.
Upholstery of an office chair does not have to be accompanied by an appeal to specialists. You can use repair tips, arm yourself with the necessary tools and materials and make an independent restoration.
Office chair repair
Often organizations donate chairs for repairs. Chair upholsteryoffice work is a simple task, but when the amount of work is large, only professionals can handle it quickly and efficiently. They can come to the office or home, measure and calculate the exact cost of the work for free. Also pick up products for repair and bring back at the set time. Often, the whole work takes no more than 2-3 days.
Not only upholstery replacement is included in the work of such firms. They can repair the chair frame itself, replace the rollers and legs, foam rubber and plywood. The cost of the service will depend on the volume and urgency of the work performed. The calculation is based on what parts were used, how much time was spent.
Price
Upholstery of office furniture is a job for a number of professionals. Now the market is replete with firms that provide such services. Often they offer the following service:
- departure of measurers to the place and drawing up estimates of work;
- chair transportation;
- dismantling the product;
- preparation of upholstery according to sketches;
- directly upholstery of an office chair;
- return of the finished product at the expense of the company.
Each organization has its own price list for the services provided, and prices can vary from 500 rubles and more. Not only the material matters, but also the design of the chair, its dimensions and the initial cost.
Upholstery of an office chair, the price of which depends not only on the cost of servicesfirms, but also on what material of a covering will be chosen by the customer, will allow to return a former look of old furniture. As a rule, the catalog is provided by the company itself, it contains both genuine leather and its substitutes, as well as textile analogues.
