Usually the hallway is small, so every square centimeter is important in its arrangement. To save space, it is better to install a small hanger, rather than cluttering the room with cabinets. Moreover, there are interesting ideas for do-it-yourself wooden hangers. It is about them that the article will be discussed.
Making a wall structure
To make a wooden wall hanger with your own hands, you will need the following tools:
- Sections of boards.
- Hacksaws with different grits.
- Awl and some hooks.
- Jig saw and screwdriver.
- You also need to stock up on a blowtorch.
First, you need to decide how long the hanger will be, and cut off a piece of the desired size from the board. Using a jigsaw, you can give the edges a round shape.
How to make a hanger with your own hands from wood? When the surface is not pre-sanded, the edges should be finished. To do this, first you need to use large, and then smallsandpaper.
When making a hanger with your own hands from wood, the surface of the board used must be treated with a blowtorch. If it is not there, the board can be burned over the burner. When doing this, be careful not to injure your hands.
The workpiece must be attached to the wall. There are several ways in which this can be done. You can attach the "ears" to the back of the board by drilling a few holes for fastening, or fix the resulting workpiece to the wall.
Hooks must be secured with screws. Such a hanger will look better if you attach antique-style hooks to it. The design will look more spacious if you choose a triple hook.
Tools for making a floor version
You can also make a floor clothes hanger out of wood. When performing such work, you can not do without a drill, self-tapping screws, a Phillips screwdriver. To make a wooden floor clothes hanger, you need to stock up on a fitting, a self-tapping screw and drills. In addition to the level and hacksaw, you will need a tape measure and stain. You will need varnish and a coarse-grained “skin” for work.
In addition, to work on a wooden clothes hanger, you will need thick wooden bars. Instead, you can use an old metal support for a Christmas tree or a floor lamp. The main thing is that the base of the do-it-yourself wooden clothes hanger is stable.
You can't do without a wooden post. How can I buy itfor a hanger in the hallway made of wood in a hardware store, or make it yourself.
You also need to prepare wood glue and metal hooks. To perform such work, you will need a piece of rubber layer (it must be glued to the bottom surface) and massive boards (they are attached near the cross). You can make a drawing of a wooden hanger in advance.
Procedure for making a floor hanger
Working on the lower part, first of all, you need to make a cross. The bars for the rack hanger must be sawn in half and sanded to remove burrs. After that, they should be connected at an angle of 90 degrees.
To make the connection tighter, use a chisel to select recesses near the elements of the cross along the entire bar. By connecting these areas, you can see that they are fixed motionless. After that, using a fitting, you need to cut out the supports of the product and screw them with self-tapping screws.
Before screwing in, a hole should be drilled with a drill so that small cracks do not appear on the wood, reducing its service life. The diameter of the screw must be larger than the diameter of the drill. Screw in the self-tapping screw only after the holes are filled with glue.
When making the upper part, the following point must be taken into account: it is better not to attach the hooks to the trunk, but first mount them on a small square. Alternatively, you can step back a little from the top and attach the bars to the trunk.
If you have to hang a lot of clothes on the product, you need todrill holes for strength and fill them with glue. To make the hanger look neat, it must be treated with stain.
If you wish, you can add creativity using original elements. For example, hooks can be replaced with cutlery or towels with branches.
Original version
How to make an original model clothes hanger yourself? For the next option, you will need a saw, a planer and several wooden boards. Also, you can not do without a drill, brush and screwdriver. In addition, you should stock up on rubber gloves and varnish.
Having made a drawing, you need to get to work. After cutting the boards with a jigsaw, the surface should be sanded. The edges of the wood used must be rounded with a boss.
Next, the tree must be varnished. To do this, apply three layers of varnish and wait until they dry. You can take a varnish of any shade.
After the varnish has dried and the workpiece is ready, you can start working on the hooks. They can be made from both metal and wood.
Using an electric or hand drill, you should drill several holes in the box and put prepared wooden rods on the glue (it is important that they protrude one centimeter). Finally, you need to drill several holes in the workpiece and insert the prepared hooks.
Wooden hanger option
You can also make a wooden hanger in a different way. For the manufacture of hooks, oak chocks that have knots should be used. The log is necessarysplit in half with an axe. The length of the knots must be 3 centimeters, and the diameter must be at least 15 centimeters.
One of the sides of the chip must be leveled with an electric planer. Next, the surface should be varnished.
Use self-tapping screws to attach the hanger to the wall. First you need to drill a chamfer with a drill, and then prepare a hole. Its diameter should be the same as the head of the screw. This is necessary so that the product is not damaged.
Wooden hanger for nursery
If desired, you can make a hanger for the children's room. To do this, prepare a blowtorch, a jigsaw and a hacksaw. You can not do without sandpaper, a screwdriver and an awl. You should also stock up on a tape measure and a pencil.
In addition, you need to prepare a few hooks, screws and wooden boards. To decorate the hanger, you should use a paint brush, primer varnish. You can't do without blanks for decoupage, scissors, glue and a sponge.
After making a drawing, you need to get a wooden board and place it on a stable support. Using a jigsaw, you need to cut out several blanks.
The next step is firing the boards. To do this, use a blowtorch or gas burner. Sawed parts need to be coated with paint or varnish.
If you want to make a hanging hanger, you need to mount metal strips by drilling several holes for mounting. You can also make through holes. After they are done, you need to skip the screws.
The final stage is attachmentto the wall of metal hangers. They can be arranged both in a certain order and randomly. To fix them, use magnets or an adhesive strip.
Hammer hanger variant
The peculiarity of such a hanger is that the hooks will be replaced with old hammers: you need to cut off the handles from them, and leave only their ends. First you need to prepare the board - sand it and cover it with a layer of varnish.
Hooks should be laid out and marked on the board with a pencil where they are attached. Next, you need to mark the location of the screws with a pencil. Finally, you need to attach the hooks.
You can attach an additional shelf for scarves, hats and other small items. They need to be done like this: having measured the distance on both sides, you should take the bracket and mark several holes for the fasteners. After drilling a hole, you need to mount the bracket.
The structure must be attached to the wall. To do this, mark the right place and make holes. The size of the drill should be the same as the size of the dowel.
Making a hanger from natural wood
You can also make a hanger from natural wood. First you need to split the decks in half. One of the sides needs to be leveled using an electric planer.
To prepare the surface for use, the wood must be treated with an antifungal agent and covered with a layer of clear varnish.
To mount the hanger on the wall, it is better to use self-tapping screws. Having drilled a chamfer, it is necessary to prepare a hole. To avoid damage to the product, it is important thatdiameter was run down with a screw.
Helpful tips
You can make a hanger out of broken coat hangers. To do this, you need to prepare a board and broken coat hangers. You can't do without glue, brushes and varnish.
The board needs to be prepared in advance: drill a few holes for fastening and attach the prepared hangers. After that, you should wait for the glue to dry.
You can also attach the back of a wooden chair to the hook from the old coat hanger. The edges must be sanded. You can cover the hanger with bright paint.
As you can see, making a hanger yourself with your own hands is not so difficult. To do this, you just need to show a desire, set aside a little time, and also purchase some materials and tools in a hardware store if they are not available at home.
