Snow is, of course, good. But when its moderate amount. And in this case, residents of the private sector are forced to constantly clean it up. It is often difficult to perform such work manually. Although a shovel is a reliable tool, it takes quite a long time to clean a large area. Let's talk about how to make a snow blower with your own hands. This will help save money and at the same time get the right equipment.
General information about snow blowers
Such a useful technique appeared a long time ago. It was invented by a Canadian who was constantly forced to fight with mountains of snow near his house. Since then, snow blowers have improved significantly and have become more productive, economical and easy to use. Before proceeding directly to the assembly work, you need to deal with the priority design. That is, it will travelthe snow blower itself or we will move it manually. The second option is cheaper and easier in technical terms. In general, we will look at several ways to make a snowplow with your own hands. To be more precise, we will talk about machines of different types. But all this in order.
Auger snow blower
As a basis, we will take an old engine from a walk-behind tractor. This motor is perfect for us. To assemble the auger body, we need sheet metal. The frame of the structure is made of a steel angle with a section of 50 x 50 mm. To organize the side parts, you need the most common 10 mm plywood. We also need something to hold on to. A half-inch pipe can be used as a handle.
The air intake of the engine, which will provide its cooling, is desirable to be additionally protected, which will prevent the ingress of small snow particles. The width of the machine in our case will be no more than 65 cm, and its working body will clear paths 50 cm wide. This will give us the necessary maneuverability and ease of movement of the unit. Well, now let's move on to the practical part and look at how to make a high-quality snowplow with your own hands.
Production of the screw
¾ pipe can be used as auger shaft. It is necessary to make a cut in it, on which a metal spatula will be fixed. The principle of operation will look likeso. In the process of working on the conveyor belt, the discarded snow will move to the blade. From there it will recline to the sides. It is desirable to equip the auger pipe in the following way. Install a metal spatula and four rubber rings on it. As a material for the latter, an old transport tape with a thickness of at least 1.5 cm can be used.
You need to understand that the screw tube will rotate in self-centering bearings. They need to be closed. This will prevent moisture from entering the case and increase the durability of the assembly. The transmission can be either belt or chain. The first is less noisy, but not too reliable, it can fail if jammed.
Do-it-yourself auger snow blower: drawings and assembly of the structure
The walls of the machine body must be larger than the auger itself. This is necessary in order to prevent the working body from touching the walls. Usually, an engine installed on a snow blower can be used on other equipment at other times. Therefore, it is recommended to provide a quick-detachable design. For this, a special platform is being built. This solution has many advantages. Firstly, cleaning the tool after work is greatly simplified, and secondly, after removing the motor, the unit will become much easier. All metal elements can be connected to each other by welding, but it is desirable to use threaded connections. Also, pre-prepare a drawing that will guide you.during assembly. The unit can then be put into operation.
Snowblower
In terms of design, this unit is not too complicated. It is great for clearing snow on areas of any size. To assemble the structure, you will need a lathe and a welding machine. In principle, such equipment can be found in almost any workshop. As a base, we will use a gasoline engine, a throttle cable and a gas tank.
First of all, you need to select a workpiece from which the rotor will be made on a lathe. If there is no desire to mess with this, then you can buy it in a specialized store for little money. Outwardly, the rotor resembles a disk. When it is installed on the hub, blades are attached to it, usually 5 pieces. The installation of the blades is preferably carried out by welding. The blades on the reverse side can be equipped with stiffeners, which will increase the efficiency of the structure and its performance.
You need to put on a casing on the fan, which will protect it from the ingress of various elements. It is worth noting that various assembly schemes for the main elements of a snow blower involve placing the cylinder head at different angles. It is best to place the cylinder at a 90 degree angle for efficient cooling.
Make a snow blower with your own hands
Our snow blower is almost ready. It remains to complete the assembly, andequipment can be put into operation. It is necessary to put a shaft on the rotor. It is mounted on pairs of ball-type bearings. Fixing to the body is best done with a clamping ring and a pair of bolts. Directly the rotor to the machine body must be fixed with a bracket. She will also hold the clamping ring, which is very convenient. It is desirable to equip the machine with removable scrapers. This is necessary in order to be able to adjust the width of the grip.
In some cases, this is an extremely convenient feature, which, by the way, is not available in all purchased models. The snow throwing range in our case will be about 6 meters, and this is with a unit weight of 18 kilograms. In general, you will get a maneuverable and lightweight unit. As you can see, it is quite possible to build a snow blower with your own hands. How to make a homemade snow blower, we figured it out. Now a few more important nuances.
Worth noticing
If any large and hard element gets into the engine, be it a stone or a piece of ice, it may fail. To prevent this from happening, add safety bolts to the design. Do not neglect the bearings of the closed type, but this has already been said a little higher. If you decide to make a snowplow with your own hands on an electric drive, you should understand that it will be effective only at short distances. Otherwise, such equipment is more economical and less noisy than a gasoline engine. But you have to get used to the wire, which will follow you everywhere. Pay attention also tomaterial used in the assembly of the structure. It should be as light as possible, yet strong. If the unit is too heavy, it will be problematic to work with it.
Conclusion
You can also make a snow blower for a walk-behind tractor with your own hands. Drawings in this case, it is simply necessary to use. It is on them that the main dimensions and design features of the unit will be indicated. In general, such a decision makes sense, especially since such equipment will move on wheels, which is very convenient.
We have de alt with this topic. There is nothing complicated, but it will take time to assemble, since you need to buy something, and carve some parts yourself. When the assembly process is completed, you can put the design in order. This refers to cosmetic work, such as painting, polishing, etc. As a result, your homemade snow blower will not be inferior to any purchased one. But you will save a significant amount, and you will gain experience in such matters and be able to give advice to beginners.
