Glass fabric wallpaper is a stylish and practical solution for decorating the interior surfaces of a room. In terms of design properties, they are not inferior to paper coatings, but at the same time they are easy to clean and endure mechanical stress. But what is the right way to glue cullet to ensure the full range of performance benefits after finishing? In general, the task is not difficult and can be handled by an ordinary homeowner, but there are a number of points that you should familiarize yourself with in advance.
What is fiberglass?
As the name implies, this type of coating is formed from fiberglass. In special factories, high-precision spinning technology produces fabric based on glass fibers, which, in turn, are made from natural raw materials - clay, limestone, quartz sand and soda. Therefore, do not confuse fiberglass with synthetic plastics and composites with toxiccomponents. Even under conditions of increased temperature loads, this material does not emit chemically hazardous substances. As confirmation of this fact, we can mention the practice of pasting outwardly unaesthetic heating equipment. For example, how to glue glass wallpaper on the stove? It is enough to bring its surface into proper form and prime it. Next, a layer of wallpaper is laid, after which it is painted with heat-resistant paint. And just in this technique of using fiberglass, the ambiguity of its intended purpose is expressed.
The function of decoration in relation to coatings based on fiberglass is not even as important as the task of reinforcement. There are special fiberglass meshes for reinforcing plaster layers, but they are structurally too coarse and not suitable for thin-layer coatings. In turn, cullet can also serve as a structural reinforcement, and at the same time convey texture patterns after the final painting.
What materials will be required in the work?
Unlike ordinary wallpaper, in addition to the adhesive, you will need a wide range of accessories. These include the following:
- Rigid fixing materials - screws and dowels.
- Elastic fixatives - self-adhesive tape and sickle tape.
- Putty for sealing seams.
- Sealants.
If there is a question about how to glue glass wallpaper on the ceiling, then it would be useful to think over its design in advance. It is one thing to cover the base of the ceiling immediately after whitewashing, and another to mount a modern suspendedceiling. In the second case, you will also need to prepare a special kit with metal frames, drywall and appropriate mounting hardware with profile height adjusters.
The nuances of choosing glue
Since glass wall papers are environmentally friendly and non-toxic, it would be reckless to use reinforced compounds with aggressive chemicals for gluing them. Experts advise limiting yourself to mild agents based on starch or PVA. On the other hand, a completely natural base, especially in conditions of high humidity, becomes a favorable environment for the development of fungi and mold. In this regard, the question arises: how can glass wallpaper in the bathroom be glued to the same glue without special protective chemistry? To do this, you need to use canvases with modern adhesive additives, in which there are antibacterial and moisture-retaining substances that are safe for he alth. This is a broad group of fungicides that prevent the development of unwanted biological processes.
Preparation of glue
It is advisable to purchase formulations in the form of a dry mix, as they retain their qualities longer and allow one package to be used in parts at different times. In the question of how to properly glue glass wall papers, the aspect of dividing work areas according to time steps is important. In other words, portions should initially be distributed among the pasting zones, since the prepared mixture retains its properties for a limited time of about 30-45 minutes. As for the preparation of the adhesive mass, this process is carried out as followsway:
- Water is poured into the prepared container of the required volume.
- A dry mixture of glue is poured out in a thin stream - so that initially the particles do not stick together, but dissolve throughout the volume of the liquid.
- For mixing, it is recommended to use a construction drill with a mixing attachment, using low-speed mode. Stirring takes 5-10 minutes.
- The cooked mass is kept for another 10-15 minutes, after which it can be used.
Preparing the surface for work
First, a set of works is carried out aimed at identifying and eliminating serious structural defects. When it comes to old walls, it is necessary to carefully check their base for the presence of flimsy areas - for example, where the plaster peels off or there are chips. Such places must be sealed with a new cement mortar, and then covered with a priming layer. In general, how to glue glass wallpaper on walls with bumps? The best option would be a combination of fiberglass coating and putty, previously applied in thin layers. Large cracks and joints are sealed with a prepared sickle mesh. At the final stage of preparation, it will not be superfluous, along with mechanical cleaning, to carry out dedusting and degreasing. The first operation is performed with a construction vacuum cleaner (or a clean wet roller), and the second with any solvent like white alcohol.
Can I glue on old surfaces?
Better of courseuse new surfaces as a draft base, but this is not always possible and technologically justified. For example, if we are talking about paintwork, which can only be removed in the process of coarse grinding with special equipment. On the other hand, gluing glass wall papers to paint is possible only if sufficient adhesiveness of the existing coating is ensured. That is, if the same putty was previously applied to the paint itself, creating the necessary adhesive function with both materials on both sides. For other old coatings like paper wallpapers, the same adhesion requirement applies, but the guarantee of reliability is also essential. The coating should not have poorly glued, peeling or other weak areas. All of them are found during troubleshooting and treated with a primer.
Step-by-step instructions for pasting
The main workflow is carried out in the following steps:
- Glue is applied to the surface from the doorway along the marked area with a brush. It is necessary to distribute the adhesive mass so that it goes slightly beyond the preliminary marking - this will exclude the preservation of non-glued places.
- Cloths are glued from top to bottom. Each strip is first glued at the top edge, then gently smoothed down towards the bottom with a rubber spatula.
- The issue of joint design is fundamentally important. How to properly glue glass wallpaper for painting - overlapOr in a joint way? Since we are talking about a thick and relatively rigid material, the butt technique will be preferable. Two edges can be brought together without a gap, while not changing the thickness of the coating in the line of convergence. After the completion of the entire operation, the joints are additionally ironed, holding both sides of the canvases.
- Excess glue is removed with a trowel and rags, after which the coating is left to dry for two days.
Selecting the side for gluing
With a cursory inexperienced glance, it is almost impossible to visually distinguish the wrong side of the glass from the front. Moreover, there is an opinion that there is no difference between them - the texture will be equally traced by the type of mirror image. But this is not entirely true, and the question of which side to glue the glass wallpaper has quite logical reasons. In at least some models, the facial texture is radically different in the configuration of the pattern, its deepening and symmetry. You can recognize it in two ways:
- In roll packaging, the outside usually faces inwards.
- There is a marking in the form of a blue or gray strip on the back side.
Pasting uneven corners
Fiberglass is not flexible and malleable enough to be easily deformed and glued in corner areas. Under the outer corners, you will have to cut the canvas along the edges, forming two divided planes. After gluing, the edges will need to be carefully processed with sandpaper or other fine abrasive. howIs it correct to glue glass wall paper in uneven inner corners? The canvas must also be cut along the ruler in the contour of the junction of two planes, observing the vertical direction of the line. It is important to consider that the bend around the corner should not be higher than 2 cm. Next, another sheet is glued, which will cover the bend. This is the case when the overlapping technique pays off when working with fiberglass wallpaper.
How to glue glass wallpaper on the ceiling?
At the first stage, the installation of the suspension system structure is carried out. A baguette with drywall is installed along the guide profiles, on the surface of which glass wall papers will be glued in the future. Further, the finishing technology is carried out according to the standard scheme, but taking into account the specifics of the location of the working plane. How to glue glass wallpaper on the ceiling? Firstly, one cannot do without the use of a ladder structure, which must be securely fixed. Secondly, you will have to work with a tool for long-term retention of the material in a state of snug fit to the ceiling. There are special paint rods and trowels with a rule, the design of which allows you to conveniently smooth finishing materials on a suspended surface. And thirdly, it would not be superfluous to include in the list of glue selection criteria such a parameter as a quick fight. There is no question of complete short-term polymerization with a sufficient set of strength for operation, but after a couple of minutes the need to hold the web will disappear by itself.
Conclusion
The use of fiberglass provides many advantages that will make surface care easier in the future. To this it is worth adding the significant advantage of this material as the structural basis of the finishing coating. This explains its widespread use in public and industrial buildings. If we talk about the shortcomings, then they are expressed in high cost and installation technology. How to glue glass wallpaper? The secret to a successful finish in this way lies in the proper preparation of the substrate and the use of the correct adhesive. If these two conditions are met, then in the end it will be possible to obtain a durable, functional and aesthetically attractive coating. Again, it can be combined with paints and varnishes. In this way, an organic combination of the original texture solution and texture corresponding to the overall interior style will be achieved.
