For a bath, you can make a stove yourself. This method will be budgetary and simple. To carry out the work, you will need a piece of a wide pipe made of stainless steel or other material. A homemade stove is a fairly economical version of a device that is used to heat a bath.
You will be able to make durable and durable equipment, the furnace and heater of which are assembled from rolled metal parts. But the water tank can be made from another part of the pipe. If you make a furnace with your own hands, then the time and labor costs will be minimal, this cannot be said about connecting parts when it comes to sheet metal.
As a result of the work, you will be able to appreciate the high level of functionality due to the tightness of the case. This will ensure the safety of people in the bath. When installing equipment, you will not need to take care of special fences.
A do-it-yourself stove for a bath from a pipe can be made in a horizontal or vertical version. Initially, you must make sure that the product is durable and that there are no damages that were caused by corrosion. This can happen if the pipe has been exposed to the open air. If you have found problem areas, you should strengthen them with steel patches. Make holes in possible areas of corrosion damage that will facilitate the functioning of the furnace.
Features of installing a steel furnace from a pipe
When creating your own stove from a pipe for a bath, you must take care of the absence of cracks and gaps in the body. The structure must be airtight. Wooden walls are covered with special antiseptic agents. Metal sheets can be sewn on them.
It is forbidden to place flammable objects made of wood, fabric or plastic near the structure. At 15 cm from the floor surface, it is necessary to equip an ash pan, which is sheathed with a steel sheet. From the upper plane to the ceiling, a distance of 0.50 m should be observed. The stove can be installed at the entrance to the bathhouse from the dressing room.
Under the very ceiling, the temperature should correspond to indicators of 80 degrees or more. At the bottom of the steam room, a temperature equal to 45 ˚С should be maintained. If the stones are well heated, this will provide enough steam when you pour water over them. Solid fuel will be evenly afterburned, which will be ensured by excellent tightness of the furnace and chimney. This also indicates a high efficiency.
Production of a vertical oven
To make a vertical stove for a bath from a pipe with your own hands, you must take two pieces of pipe, one of which will be 0.5 m long and the other 1 m. These pieces will be enough to make high-quality heating device. The foundation width must be 0.5 m greater than the pipe diameter.
A reinforced layer of metal rods is laid on top of the base. You will need to make a concrete screed. The thickness of the foundation is more than 20 cm. As soon as the building material hardens, ordinary bricks or paving slabs can be laid on the floor.
If you decide to assemble a stove for a bath from a pipe with your own hands, then the base for the structure should also be arranged independently. This part is made from a piece of pipe. In order for the device to stand securely and firmly, the lower edge of the product is aligned. A cutout is formed through the blower, the size of which is 5 x 20 cm. This part of the stove should act as an ash pan. The bottom of the firebox is welded on top of the blower into the pipe. For this, a sheet of metal is used. Its thickness should be 12 mm. A circle should be cut out on it with a diameter that is equal to the corresponding pipe parameter. In the central part of the part, a cutout is made for the grate. You can buy it ready-made or make your own. In the latter case, a lattice of steel bars is welded into the cutout in the circle. Gaps should be equal to their section.
Stepping back from the bottom of the firebox 5cm, you should form a cutout where you will supply fuel. The door is hinged. In order to make a furnace from a profile pipe with your own hands, you must supplement it with a cutter, it is necessary for the upper part of the furnace. To do this, take a metal rectangle with cut corners. The part should be inserted into the pipe and welded at the edges of the cuts. The size of the gap will allow smoke to escape from the furnace and circulate along the walls of the structure, contributing to heating.
Work methodology
At 8 cm above the cutter there should be a lattice of bars. The diameter of the workpiece is 15 cm. It will serve as the bottom of the heater. The door for it will resemble a firebox door.
The upper part of the heater must be welded with metal, in which a hole should be made for the chimney. If you will use a removable water tank, then there should be stops on top of the heater, which will help to stabilize the tank. The pipe can form the basis of a water tank. The parameters of the lower plane must be equal to the same dimensions of the upper part of the heater.
In the center of the tank, a pipe should be attached to its bottom, its upper edge must be 25 cm higher than the edge of the tank. For the tank, a cover should be made in the form of two semicircles. A faucet is installed slightly above the bottom, and the container must be welded to the top of the heater.
Horizontal oven
If you will make a horizontal bathoven from a pipe with your own hands, you should know that the design will involve an external heater and a hinged tank. Among the features, it is necessary to highlight the increased depth of the furnace and the compactness of the product, which will contribute to the rapid heating of the room. The stove can be installed so that the combustion door opens into an adjacent room.
The manufacturing process consists of several stages. At the first, a workpiece must be cut off from a metal pipe. Its length will be 80 cm. The trimmings must be aligned. The diameter of the pipe should be 50 cm. A sheet of metal should be used for the grate platform. Its thickness is 12mm.
A rectangular part with dimensions of 40 x 80 cm is cut out of the material. In the central part of the workpiece, it is necessary to make an opening where a grate or a home-made grate of bars is welded.
When making a horizontal oven from a pipe with your own hands, you must weld the grate platform into the pipe. In this case, the weld will be located under the part. This is due to the fact that the welding area is most often the most vulnerable spot. This knot will burn through when exposed to fire.
For the facade of the structure, a sheet of metal is used, from which a rectangular blank is cut. On the one hand, it must be rounded. In the front part, the dimensions of which will be 60 x 70 cm, it is necessary to make openings for the blower and furnace doors.
The back side will be metal. Its dimensions are 70 x 90 cm. When cutting off the upper part of the rectangle, there is no need to round off, because the corners willserve as constraints. By the way, it will help to make a stove from a pipe with your own hands, a photo of such structures. Perhaps they will let you know how to proceed. But in the described case, you must follow the instructions. We agree with her that at the next stage it is necessary to make connections between the rear and front parts. They are attached to the body. It is necessary to fix the heater limiter. This device is a part whose upper contours must follow the outlines of the back wall. The bottom contours are streamlined.
In the place where the chimney should be located, a square hole with a side of 15 cm should be made. An arch should be formed from a metal sheet on top with an opening for smoke to escape. Keep the same distance between the hole and the opening. The kink is necessary for afterburning the fuel and cutting off the flame.
The chimney is located on top. The volume of the stone compartment can be increased by 20 cm by welding a metal grate. When making a stove with a standing pipe for a bath with your own hands, you must install the doors in the openings for the blower and the firebox. Finishing the furnace at the final stage involves grinding the surface to remove rust spots and scale. In order to give the device greater aesthetics, polymer heat-resistant paint should be used. In order to eliminate the unpleasant smell when baking the substance, the oven should be heated before it is installed in the room.
A concrete base is required for the installation of the structure. You can use single-layer brickwork as a foundation. You canalso apply porcelain stoneware or paving slabs. If you comply with fire regulations, then you need to equip the refractory insulation. A chimney is led up through the ceiling and roof of the bathhouse. A shelf must be welded to the back of the oven, where the water tank is installed. At the last stage, the heater should be filled with stones.
What to look out for
Before starting work, you should definitely consider the drawings of furnaces from the pipe, with your own hands in this case you can easily cope with the work. But this is not yet a guarantee of success. In order to prevent heat from blowing out of the furnace, a valve should be provided during manufacture, which will be located on the chimney.
When soot accumulates in large quantities, fire may occur. This can be avoided if the horizontal unit is equipped with an afterburner. At a certain point in the pipe, two holes should be made where metal tubes are installed. They should bend to the side. This will prevent excessive soot formation. More oxygen will get into the furnace, which contributes to the burning of the fuel and the formation of less soot.
530 mm pipe oven
Vertical furnaces from such a pipe are quite easy to make. But this option is not the most practical. At the first stage, it is necessary to make the formwork and lay out the reinforcement inside. The space is poured with concrete mortar, which will make it possible to obtain a foundation for the heater. He is being coveredseveral rows of brickwork laid on clay mortar. The foundation at this stage is left to solidify.
Many are wondering if it is possible to make a sauna stove with your own hands from a 530 mm pipe. The answer here is positive. If you also want to use a pipe as the basis for the body, then you must definitely align the edges of the workpiece. In the future, the pipe will be used as a base. To fix the grate, small holes should be cut. One large hole will be needed for the blower. If you decide to do everything yourself, then you can also make a grate with your own hands. To do this, you need several metal rods. Cut off is located above the firebox. The sheet of metal is cut off at the corners. The heater is located 10 cm higher. It is covered with another sheet of metal with a hole.
Installing the oven
If you decide to make a stove from a pipe with your own hands, then you must install the structure yourself. When it is ready, you should ask what the rules are. First of all, you need to observe the size of the site where the device will be located. The base should be a square 70 x 70 cm. The height should not be more than 20 cm. Having retreated the same amount from the wall, it is necessary to install the stove on the foundation.
The structure is fixed with clay. In the place where the pipe outlet will be located, a thickened brick laying by 12 cm should be made. The wooden floor is covered with felt, which is pre-impregnated with a clay solution. Cardboard can be used instead of feltor asbestos. A mandatory procedure is impregnation, which is necessary for fire resistance. The pipe gap between the ceiling and the roof should be plastered and whitewashed with lime. The outer laying of the pipe is taken out 50 cm above the roof level. Otherwise, there will be no traction in windy weather.
The door of the heater must be directed diagonally into the corner of the room. Fuel doors turn towards the exit. When making a stove from a pipe with your own hands, you must also take care of the location of the shelves in the steam room. They should be located near the same wall where the heater is installed. You should not touch the hot ceiling with your head. The height of the shelves should be calculated before you make the oven.
It is important to follow fire regulations. In a wooden bath, a metal stove is lined with bricks or cobblestones. The latter is used for beauty. The cladding should be done on both sides of the structure, its height should be 120 cm. Next, proceed with the construction of the wall.
Making a rocket furnace from a square pipe
To carry out work on the manufacture of a rocket furnace from a profile pipe with your own hands, you will need a square-section pipe, which is cut into blanks. They should be marked so that one of the edges is 45 ˚. In this case, you need to use a grinder. The pipes are welded together, which in the end will allow you to get a design that resembles the shape of boots.
You can easily make such a square pipe oven with your own hands. The structure is also called"Robinson". In the next step, you must make cuts on the sides and top of the pipe. Their dimensions are 20 mm deep and 3.5 mm wide. This will make a stand for the container.
The rest of the strip is cut in half with dimensions of 30 x 5 cm. Its thickness is 3 mm. The second strip of steel should be marked in the middle. Its size should be the same. Elements are welded to it in such a way that a cruciform shape is obtained. Steel strips in the amount of 2 pieces and the remaining 14 cm pieces must be welded into a frame that will be retractable. Elements are welded with an overlap.
When making a stove from a pipe with your own hands, in the next step, on top of the finished frame, using a welding machine, you must attach the finished grate. The distance between the rods should be 1 cm. A stand should be placed on top of the pipe, while the grate is pushed into the furnace hopper. At this stage, we can assume that the main work on the manufacture of the furnace is completed. Tests can be carried out at this stage.
Solid fuel is put into the furnace, the device is melted. If you have not identified problems in the work, you can wait for all the elements to cool. At the final stage, work is carried out on painting the furnace. This will protect the material from corrosion. For this, heat-resistant paint is used. The operating comfort can be improved by welding the handle to the combustion chamber door.
Preparation of materials and tools for the furnace from a 500 mm pipe
A do-it-yourself oven from a 500 mm pipe can be made almost according to the same principle,which has been described above. For work, you will need a piece of metal pipe, the length of which is 1.5 m. You will need a 50-centimeter segment by 350 mm, as well as a metal sheet. You should purchase ready-made doors and metal hinges. You should have a grinder and a welding machine in your arsenal.
Work algorithm
A do-it-yourself oven from a 530 mm pipe can be made using the same technology, which will be described below. At the first stage, a piece must be cut out of the pipe, the length of which should correspond to the length of the body. This value is approximately equal to 0.70 m. The cut points will be sharp, so they need to be sanded. At the bottom there will be a grate. A rectangle should be cut out of the metal plate, which will correspond to the internal dimensions of the furnace.
The middle of the rectangle is cut out so that there are places for welding along the edges. Metal bars are welded horizontally or vertically at a small distance from each other. The weld seam is recommended to be placed under the grate. At the next stage, when making a furnace from a profile pipe with your own hands, you will need to weld the back of the structure. To do this, a workpiece is cut from a sheet of metal with dimensions that are slightly larger than the diameter of the pipe.
If there is a heater in the upper part, then the length of the sheet should be increased by the size of the compartment. This will eliminate a large number of welds. Next, you can prepare a sheet for the facade. The dimensions of this part should be slightly larger than the dimensions of the furnace. cut in the sheetrectangle for the furnace door and blower. The facade sheet is reinforced to the front of the furnace. In the upper part of the body, it is necessary to make holes of a square size, the size of which will be 15 x 15 cm. This is necessary for installing a chimney. Next, you can start hanging the doors. The finished oven is cleaned, and then you can paint it with heat-resistant paint or overlay it with brick.
The oven for a cauldron from a pipe
Now you know how to make a rocket furnace from a profile pipe with your own hands. But you may find it useful to use technology that involves assembling a heater for installing a cauldron. The bottom of the pipe must be cut off with a grinder. Closer to the bottom, a furnace hole should be cut. Its shape can be rectangular or semicircular, depending on taste. This will not affect functionality in any way.
The separated piece should not be thrown away, as it can become a door or a damper. By turning the cylinder over and stepping back from the top edge of 100 mm, it is necessary to create a hole for the chimney pipe. Using a drill or grinder on the sides, several through openings should be made. Using a welding machine, the chimney part is welded into a single structure of two pieces, which are connected to each other at an obtuse or right angle. You can use an elbow to connect.
When making a stove for a cauldron with your own hands from a pipe, in the next step you must weld the chimney to the hole previously made on the body. The next step is to installprofiled pipes or corners that will act as legs. You can use four or three supports. Keep the same distance between them to make the oven stable.
Now you can make the bottom of the lattice or metal sheet. Handles are fixed at the top of the structure. On one side of the firebox and on the piece of metal set aside, 2 or more holes must be drilled. A wire is threaded through them, which will act as loops. This will allow you to get a homemade furnace door. All burrs are cleaned, other design flaws should be eliminated at this stage. Now you can apply fireproof paint or oven varnish, only after that you can consider that the work is completed.
