Currently, most smartphone users have headphones. They allow you to listen to music, audiobooks and other files from your phone anywhere. Therefore, the question of how to fix headphones from an iPhone arises quite often among users.
Many people think that in the event of a breakdown, the only way out is to throw away the headset. However, you should not do this, since most breakdowns can be repaired at home and with your own hands.
Causes of failure
To figure out how to fix the wire from the headphones or another part, you should find out what could be the reasons. This may depend on the method of solving the problem. The reason for the repair can be:
- Plug broken. This situation happens when the base of the headphones was pressed down with something or the wire was simply frayed, and the contacts lost their functions.
- Cord damage. This problem could be caused by pets, or the headphones have been used for a long time, and the wire is simplydamaged.
- Faulty volume control. This situation is not frequent, but it also occurs among users.
There are, of course, obvious damages in which the question of whether iPhone headphones can be repaired becomes negative. Such breakdowns include a broken wire or complete damage to the ear part.
Identifying the cause
To determine which part has a problem, you can use the following methods:
- Having connected the headset to the phone, you need to move the wire in different places: at the plug, near the ears themselves, at the volume control. If the wire is damaged, then when it moves in the headphones, it will either disappear, then sound will appear or crackle will be heard.
- If the buttons of the regulator do not affect the volume, then you can carefully open the mechanism and look at external defects. They usually catch the eye right away.
- The problem may also lie in the plug. To determine, it is enough to move the plug connected to the phone in different directions. In such a situation, the sound will also change.
Now let's look at ways to fix the headphones, in each situation.
Damage to the wire near the plug
The first step is to check the area near the base. In most cases, the problem comes from damage in this particular place. The wire is very mobile near the plug, so over time it simply wears out and stops transmitting signals to the ears.
Before you fix the headphones from the iPhone,you need to prepare all the necessary tools and parts:
- Old headphones, or rather a working plug from them.
- Soldering iron. Without it, it will not be possible to correct the situation, since the difficulty lies precisely in the wires.
- Stationery knife.
- Insulating tape.
Now you can start the process itself:
1. First you need to remove the plug from the headphones, as it is not suitable.
2. From the old headset, you also need to cut off the plug and open it. This is done with a utility knife. You need to cut the shell and remove the base. You can see several wires of different colors that are responsible for the right earphone, the left earphone and the general connection.
3. On a piece of paper, write down the location of these wires in order to solder them correctly in the future.
4. For another headset, you need to free some length of wires from insulation with a clerical knife.
5. In order for the repair to proceed properly, it is best to burn the ends of the wires with fire.
6. Now you need to solder the ends to the old plug. It is necessary to follow according to the drawn diagram in order to correctly correlate the details.
7. You can check the headphones by connecting them to your smartphone and turning on the music. If all is well, then move on.
8. Next, you need to protect the place of soldering with electrical tape.
This completes the operation. Such a scheme is also suitable for solving how to fix the right earphone from an iPhone and the left one.
Wire defects
Veryit often happens that some section of the wire breaks, and because of this, the headphones start to work poorly. This is checked quite simply: with the music or audio file turned on, you need to feel the wire along its entire length. If, while touching any area, you hear that the sound begins to disappear or change, you need to mark this place in order to act on it later.
Now let's figure out how to fix the wire from the iPhone headphones:
1. The first step is to buy a new wire, which will replace the old one.
2. For older headphones, you need to remove the cable. To do this, you need to disassemble the ear parts of the headset with a clerical knife. Inside you can see the wiring soldered to the board.
3. You should remember the location of the wires and solder the new cable in the same way.
4. The plug must also be disconnected and connected to a new cable. How to do this is described above.
Problems with volume control
If the sound in the headphones disappears due to the buttons on the headset designed to switch the volume, then the solution is quite simple. You need to open the panel with a knife or other sharp object.
The chips and contacts should be lubricated with graphite grease to bring them to work. After the operation, there should be no problems with the headset.
Tips
- All Apple devices, including the headset, are glued and assembled tightly and with high quality. When disassemblingheadphones, this gluing is broken, which means that you can simply ruin the device. It is best to purchase a special glue. You should also pay attention to the fact that all the parts are perfectly matched, so it will be problematic to pick them up without damage. You need to be extremely careful not to spoil the thing.
- Don't solder the contacts too carefully. Due to prolonged thermal exposure, parts may be damaged and never work again.
- From the very beginning, it is best to test your strength on cheap headphones that you won't mind ruining. You should carry out all the actions that will be performed on the main headset. If everything went well, then you can already repair the headphones from the iPhone or another expensive headset.
- If you don’t have confidence in your abilities or you don’t have the skills to use a soldering iron, it’s best to take the headphones to a master who will fix them without any problems.
- After attaching a new plug, you can fix it with a part similar to the one that stood before at the base. A pen cap that can be glued on with glue is perfect.
- The question may arise about how to fix one earphone from an iPhone. In such a situation, you should not try to operate on one part. It is also necessary to replace the entire structure, since all the parts are interconnected.
Conclusion
As you can see, the repair process is quite simple. You just need to have basic soldering skills, as well as accuracy and patience. If you try, then the question is how to fix the headphones fromiPhone, will not cause any difficulties.
