When cold weather sets in, many garage owners are wondering about heating. This is especially true for those rooms in which people are from time to time. It is impractical to equip a stationary system in them; in some cases, such an approach is completely impossible to implement. However, it is impossible to do without heating. You can equip a system that runs on electricity or solid fuel. Among the second options, a potbelly stove from a gas cylinder can be distinguished. Even the master who does not have enough experience will be able to do such work.
Recommendations for work
If you make a potbelly stove from a gas cylinder, it will be a practical solution for rooms that occasionally need heating. Such an oven heats up quickly enough, while a comfortable temperature can be achieved in a short time. It is worth considering that the oven cools down just as quickly, which is its main drawback. Solve thisproblem can be created by creating a brick shirt. However, the master must leave a small gap between the metal and the masonry. Only in this way the equipment will quickly warm up and cool down further.
When making a structure, holes should be made on the body in the amount of 2 pieces. Their shape should be rectangular. One is useful for loading fuel, while the second will act as a blower. The body acts as the main structural element, among other things, the system has a chimney.
Quite often during the manufacturing process, the blower is combined with the compartment where the ash is collected. It is recommended to equip another door here, which will make it easier to clean the structure. The principle of operation of the equipment is quite simple. Fuel should be placed in the furnace, during the combustion of which heat will be released, heating the metal of the case. The latter, in turn, will give off heat to the air, quickly warming up the room. When a potbelly stove is made from a gas cylinder, it is equipped with a chimney that will remove harmful combustion products from the room.
Nuances of the work
The master must take into account that the chimney, which has a short length, will remove heat along with smoke to the outside. Such an approach cannot be called rational. That is why the pipe must have a broken shape. It will improve the efficiency of the furnace. Almost anything that can burn can be used as fuel for the system. It maybe coal, firewood, old clothes, carpentry waste, household waste and so on. Another plus of the potbelly stove is that its design is universal and simple. Thus, the equipment can be used not only for heating, but also for cooking.
Work technology
If you will be making a potbelly stove from a gas cylinder, then you need to start manipulations with preparatory work. This procedure is mandatory, otherwise the gas that remains in the container may cause an explosion after interacting with the spark generated during cutting. First you need to unscrew the cylinder valve, allowing the gas to escape. At the next stage, the container is turned over, which helps to get rid of condensate. It should be noted that it has an unpleasant odor. Therefore, it is recommended to collect it in a container. If drops fall on the floor or other surface, weathering will take a long time.
A potbelly stove from a gas cylinder can only be made after careful preparation of the body. The container should be installed vertically, and then it is filled to the top with water. This will help any remaining gas that may have been left inside to come out. Then the container is turned over on its side, and the water is drained. The balloon can now be manipulated further. After the preparation has been completed, the master must decide what type of oven will be. It can be vertical or horizontal.
Productionhorizontal design
A potbelly stove from a gas cylinder, the drawings of which are presented in the article, can be located horizontally with respect to the plane. To begin with, the upper part of the balloon is cut off. Then a grate should be installed inside the container. It is most often formed from reinforcement. The bars should be carefully bent with a snake. Installation of grates is quite easy. They are mounted in a container and fixed with a welding machine.
Front manipulation
Now it's the turn of the front. To do this, take a steel sheet, on which a circle outline is outlined. The diameter of the latter should be equal to the outer contour of the container. Next, the master can start cutting out the part. Inside the circle, two rectangular holes should be outlined. The first is necessary to supply fuel to the chamber, while the second is intended for the blower.
Assembling
When a potbelly stove is made from a gas cylinder, the drawings help to carry out the work without making mistakes. At the next stage, you can start cutting holes in a previously prepared circle. To do this, use a grinder or a chisel. Curtains must be welded to the finished cover and the doors fixed on them. The latter are glued along the contour with an asbestos cord. This design is attached to the cylinder by welding. At this point, we can assume that the front of the oven is ready.
Now you can proceed to the back. A chimney is installed there. To do this, a hole is made, the diameter of which is equivalent to the diameter of the pipe used to remove smoke. A chimney of the required shape and dimensions is attached to it. A thick-walled pipe should be used for the chimney. After that, the oven can be used, as it is completely ready for use.
Production of the vertical structure
A homemade potbelly stove from a gas cylinder can also be vertically oriented. In the manufacture of such a design, the system can have two versions. The first provides for more manipulations that are associated with cutting. But during installation, you will face much less difficulties. When choosing this method with the help of a grinder, you should get rid of the top of the container. The second way will save time and effort. But it is considered extremely inconvenient. When a pyrolysis potbelly stove is made from a gas cylinder using the second method, the upper part remains in place. On the front, a large furnace hole should be cut. Below is a hole for the blower and ash cleaning.
Conclusion
You can place the holes arbitrarily. The main condition is that there are two rectangular holes in the lower part. Now the grates are being prepared. They are welded between rectangular holes. When the stove-stove from a gas cylinder is performed according to the first method, then install the gratesimple enough. Whereas in the second method, the grate should be installed through the top hole.
