Sooner or later, in any office or office, the question arises: how to refill printing with ink. It would seem that a fairly simple task requires certain knowledge and skills from the person performing it.
Types of seals
To know how to properly fill the seal with ink, first you need to figure out what types of ink there are.
We all remember stamps from childhood. They are easy to use, but not exactly convenient. Along with the stamp itself, you should always carry an ink pad, which is located in a separate box. This is a good option if printing is used at one workplace, but if mobility is needed, you should look at other types.
Auto tooling printing is more practical to use. It is both compact in storage and more convenient for making clear and even prints. But some difficulties are possible with it, because you need to clearly know how to fill automatic printing.
Flash stamps are the hardest part. In their design, a pillow with paint is not foreseen, which is refilled directly into the matrix itself. In addition, this type of seal often comes in several colors, which further complicates the task.
Which ink to use?
Before you can correctly fill the print with ink, you need to select them. The best option is if you take the paint of the same manufacturer that was used earlier. But it is not always possible to recognize its brand. Therefore, it is worthwhile to carefully approach the solution of the issue.
Inks are divided into water, oil and alcohol. For official documents in offices, the most common ones are most often used - water-based. They are well absorbed by paper and do not smear. But moisture can leak, which indicates the nature of their base.
Alcohol ink is used for non-porous surfaces such as glass and metal. A characteristic feature of these paints: they dry quite quickly, do not smudge and are difficult to erase from surfaces.
Oil ink is the least common. They are used in production for marking parts and boxes. Works well on both porous and smooth surfaces. They leave a massive greasy mark on paper.
When you have decided on the ink, you should not forget about their color. Mixing different colors on the same pillow is strictly prohibited. Now you can take a closer look at how to refill the print with ink.
Easiest options
Oddly enough, today the simplest form of stamps is still quite often used, which require a separate ink pad. Addressthey are the easiest.
Open the box with the porous substance and carefully drip a small amount of paint onto it. The main thing is not to overdo it, otherwise the prints will then look like blots, and their text will become illegible.
We wait until the paint is evenly distributed over the surface. If desired, this process can be accelerated by stretching the ink over the surface with a paperclip. After the porous substance is completely saturated, we make several test prints. If the print makes them clear, then everything is fine. But there may be other options.
If the prints are not clear, you need to add a little more ink and repeat the procedure again, because you already know how to refill the stamp.
When prints are blurry, there is too much ink. They can be removed with any porous paper such as tissue paper or toilet paper.
How to refill automatic printing?
Stamps in mechanical equipment are characterized by the fact that they do not have a visible ink pad. To get it, you need to show some skill.
Press a little on the lower part of the mechanism and use the buttons to fix it in a position that opens access to the pillow. With a light finger pressure to the side, pull it out of the snap and place it on a flat, clean surface.
Next, use a syringe or a special bottle with a thin nose to apply ink approximately 2 mm thick. With a paper clip or similarspread the paint over the surface and let it soak in. Remove the remaining ink with a tissue or handkerchief.
After an hour or two, put the pillow back in place and take some prints. If you did everything right, they will be clear and bright. The main thing at the time of refueling is to make sure that dust, dirt or lint does not get on the pillow itself.
The highest level of excellence
The hardest part is figuring out how to load flash print. The thing is that she has the most unusual design. To begin with, we will disassemble it by removing the locking ring with a knife. Next, put the matrix on a clean substrate on a completely flat surface. Using a syringe, carefully drip paint onto its surface and try to distribute evenly.
For the seal to be fully saturated, leave it for a few hours and then check by making a few prints on a blank sheet of paper. But before that, it is still worth removing excess moisture on its surface. This is done with good porous paper.
If the quality of the prints is satisfactory, you can assemble the flash print by repeating the reverse of the disassembly steps. If the impressions are not clear enough, it is worth refilling the porous substance of the stamp.
Multicolor printing
It has already become clear to everyone how to fill the stamp "Copy is correct", "Sold", "Paid". After all, they use only one color of ink. But there are some stamps that have multi-colored pillows. They are refueled in the same way as monochrome ones, but with some features.
First of all, you can't letmixing paints. The easiest way in this case is to refill each ink separately. First, it is applied to the central part and evenly distributed. Here you should be very careful not to overdo it, otherwise it will go beyond its zone.
After one color has been absorbed, we carry out the procedure with the next one. And so on until all zones are filled. This procedure will take a decent amount of time.
Flash prints of two or more colors are loaded from the print side. First, the central part is poured, and then its edges. Here you also need to be extremely careful so that the colors remain in their zones.
Common mistakes
And now let's look at options on how to refill printing with ink. After all, its quality and service life depend on it.
In order not to fool around with disassembling the equipment, many office workers drip paint directly onto the matrix. This is not correct for the reason that not enough ink gets into the ink pad. It is also not evenly distributed.
It is also not recommended to drip paint into a pillow that has not been taken out. This does not allow you to control its quantity. The ink will also not be able to absorb well.
Do not dip the removed pillow directly into the paint. In this way, you oversaturate it and ruin it. It is also not advisable to do this with flash printing. The effect will be the same.
In order for the stamps to serve for a long time, they need care and proper charging of the pillows.
Somesubtleties
The option that describes how to fill a rectangular stamp, as well as a round one, does not always pass. First of all, the official stamp of the enterprise is never refueled. It changes the pillow every time. This is due to the fact that the color and composition of the print should always be the same.
It is not recommended to fill the pillow more than three times. During long-term operation, dents remain on it, which significantly reduce the quality of prints.
Also, many manufacturers generally do not recommend adding ink to the ink pads of automatic equipment. According to them, the pillows themselves are not designed for this and still will not give such clear impressions as new ones. But this nuance is more of a commercial nature, because the pillow is more expensive than a bottle of stamp paint.
When working with any prints, you must be extremely careful and avoid the slightest chance of contamination, because dust, sand and hair will significantly affect the clarity of subsequent prints.
Trust the professionals
Finally, I would like to remind you that everyone already knows how to refill printing with ink, but not everyone can do it. This is especially true for complex multi-color stamps. Therefore, in order not to risk a lot of money, it makes sense to contact a special service that will do everything for you. In this case, you will spend a symbolic amount, much less than what you have to pay for a new tooling or seal. This is just the case when the risk of yourself is notjustifies.
