Do-it-yourself firewood can be made with ease, but before that you need to decide how much fuel you intend to put in it. Only with the use of high-quality dried fuel can you get good steam in the bath and the heat that the structure radiates for heating the room. In addition, only with dry firewood can you cook barbecue according to the rules. If you do not want to fill the shed with firewood anymore, since there is already little free space in it, then you can make a firewood shed yourself. It is important to find a place for it so that it is possible to guarantee fire safety. Thus, the firewood rack should not be located so close to the residential building.
Choose size
Do-it-yourself firewood rack can have different sizes. The one that has large dimensions can be located on the street, and the one that will be used every day can be located in close proximity to the stove orfireplace. This will eliminate the need to go out for firewood every time you need to light the hearth. The described special place for storing a small portion of logs must also comply with fire safety rules, which indicates the need to give the structure the ability to ventilate. But as for the external firewood, it must be made such that it has a canopy, because water should not get on the fuel.
Varieties of firewood racks
If you make a firewood rack with your own hands, then you must adhere to certain recommendations on the design parameters. Thus, if you want to acquire a firewood for temporary storage of fuel, then its capacity should be in the range from 0.5 to 1.5 m2, this is enough for a bath. Whereas if it is supposed to make a firewood for cooking barbecue and other dishes, then this figure may be somewhat smaller, it can be limited to sizes of 0, 2-0, 4 m2. A do-it-yourself firewood rack can also be portable, so that it is convenient to bring it to the barbecue. Its capacity can be 0.3m2.
Features of firewood racks
If you need to use a place to store fuel when lighting a fireplace or stove, then you can use wood or metal as a material for making. Less commonly, such firewood from willow twigs is made, but they look very original and harmonious. as the mainThe features of the portable fuel storage are the low weight of the product, in addition, the design should have an impressive capacity, but you should not be zealous with the latest quality, because you can get an installation that will take up too much space, and it will be inconvenient to use it as a portable tank.
Do-it-yourself firewood in the country should be made in such a way that the bottom is solid, this will prevent debris and all kinds of wooden debris from falling out. If a portable firewood rack is being made, then it must be made with handles. When making a firewood storage that is intended to be used only in the house, wheels can be attached to the bottom.
Preparation of necessary materials
Do-it-yourself firewood for a fireplace can be made independently if you manage to prepare some materials and tools, among them you should definitely highlight:
- Wooden bars that will form the basis of the frame of the product. The cross section of these elements should be equal to 50 x 50 mm.
- Tes for making a roof batten system.
- Boards for floor mounting.
- Slate sheets that can be replaced with other covering material.
- Nails designed to work on slate.
The amount of building material will depend on the dimensions of the structure. If the firewood shed is installed on the street, then its side walls will also have to be protected; for this, a profiled sheet should be used. However, sheathe the sidethe walls can also be cut.
Technology for making firewood racks
Do-it-yourself firewood in the country should be installed using a special technology, the features of which will be described below. As soon as you manage to choose a place for installation, you need to prepare four pits, in each of which a pole will be mounted. Depending on the capacity of the firewood shed, the distance between the supports should be determined. It can be conditionally considered that the length of the place for storing fuel should be about 3 meters, while the width should not exceed 1.5 meters. As supports, it is necessary to use a paired beam, the cross section of which is 50 x 50 mm. It is necessary to deepen the pits by 40 or 50 cm.
The front and rear supports must have different lengths. This indicates that the pieces of timber, which will be located behind and in front, should have a length equal to 2 and 2.3 m, respectively. At the next stage, they must be installed in ready-made pits, and then covered with stones and clay. Each of the materials is poured separately so that it is possible to ram. It is necessary to protect the backfilled part of the supports with a special material, which can be used as adhesive tape or roofing material. This will guarantee a higher degree of moisture insulation of the structure.
Installation of strapping
The binding of the mounted poles must be done using a beam, this must be done at three levels. Bars that shouldlocated in the lower part, must be strengthened in increments of 10-15 cm from the construction platform. As for the next beam, its fixation should be made to the central part of the supports located at the back. After that, you can proceed to the manufacture of the upper tie, which is mounted on the rear and front poles along their upper ends.
The side supports must be fixed to each other by means of a beam at three levels. The structure will become more durable and stable if braces are attached to its rear and side bars.
Roof Arrangement
Before you make a woodcutter with your own hands, you need to think about whether it will have a frame sheathing. In favor of this, we can say that such a design will protect firewood from precipitation. Due to the fact that the pillars have different lengths, the master will have the opportunity to equip a pitched roof. You can take other sizes of posts, but the example uses a difference of 30 cm.
When a do-it-yourself firewood rack is made, projects must be prepared in advance. You can see them in the article. At the next stage of the work, you can start laying the crate, which is mounted on the top screeds. If there is a desire, then insulating material can be laid on the roof. Slate can be used as a covering material.
Make recommendations
When a do-it-yourself outdoor firewood rack is made, logs should be laid on the soil under the boards, the step between which should be 1 m. This will allowget additional ventilation for the firewood. If the structure is installed on a solid surface, then this method should be abandoned. Wall cladding should not be made deaf, but grooves should be left for better airflow. This is how a do-it-yourself woodcutter for a fireplace is made. Projects of this design can be seen in the article, it can easily be done independently.
