C10 corrugated board is one of the widely used products in civil and industrial construction. Most often, the galvanized profile is used in the construction of individual residential buildings. The material gained high popularity not only because of the low cost compared to analogues, but also due to the successful combination of lightness and strength, as well as ease of installation. This allows you to save not only at the time of the purchase, but also during the construction process.
Scope of application
One of the reasons for the high popularity that C10 corrugated board has is its versatility. The material is used in almost all areas of construction: in the arrangement of roofing, the construction of prefabricated buildings and structures, frame, insulated wall and panel structures, fences, fences, ceilings, and prefabricated sandwich panels.
If it is necessary to lay C10 as a roofing deck, you should initially equip the crate, while the step between the elements will be 0.5 meters (but not more than 0.8). This indicator is relevant for roofs with a large angle of inclination. C10 corrugated board is manufactured according tostate standards R 52246-2004 using cold-rolled steel, which is protected by hot zinc coating. C10 with a polymer coating has gained the greatest popularity. The decorative protective layer makes the material attractive in appearance and increases the service life of the profiled sheet. On sale you can find C10 profiled sheeting with a one-sided coating, where a special varnish is applied to the inside. A sheet with a double-sided coating is used for the construction of fences, which makes it possible to ensure the same aesthetics of the fence on both sides. The stores sell C10 corrugated board from some manufacturers, which has a figured texture and is intended for the construction of residential fences.
Specifications
If you want to choose the right material, you should pay attention to the numbers that are indicated next to the marking. As an example, you can use the designation C10-1000-0.6, from which you will learn that in front of you is a wall sheet with a trapezoid height of 10 mm. The useful web width is 1,100 mm, and the metal thickness is equivalent to 0.6 mm. The modern consumer is invited to purchase material marked C10-1000-0.5 and profiled sheet C10-1000-0, 7. The first of those mentioned has a sheet thickness of 0.5 mm, while the thickness of the second is 0.7 mm. One square meter of thinner profiled sheet weighs 4.6 kg, while a 0.7 mm sheet will weigh 6.33 kg.
Despite the fact that the difference in thickness between these types of material is insignificant (the second weighs1.73 kg more compared to the first), it increases the load on the system, which is especially true for large roofing sizes. Therefore, when purchasing C10 corrugated board, it is necessary to calculate the roof area, which will be affected by the snow load characteristic of a particular region. The dimensions of the sheet differ in the width of the original workpiece. This parameter can be 1000, 1100 or 1250 mm. There is also a useful width, which is 900, 1,000 and 1,100 mm.
Material weight depending on thickness
C10 decking, whose weight varies with thickness, has a steel density of 7,800 kg per cubic meter.
- One linear meter of the product will weigh 4.45 kg if the thickness of the sheet is 0.4 mm. In this case, 4 kg will fall on a square meter.
- When the thickness is increased to 0.45mm, the weight will be 4.05kg per m2 and 4.78kg per m.
- A sheet thickness of 0.5 mm gives a weight equivalent to 4.6 kg per m2 and 5.4 kg per linear meter.
- Product 0.55 mm has the following indicators: m2 - 5.4 kg, and p / m weighs 5.9 kg.
- With a slight increase in thickness to 0.6 mm, a running meter of the product will weigh 6.4 kg, and a square meter will weigh 5.83 kg.
- A sheet of 0.7 mm has a weight of 6.33 kg per square meter, and a p/m weight of 7.4 kg.
Additional Features
Profiled metal sheet has a certain rigidity and strength, which was achieved thanks todeep 10 mm corrugation. This allows you to use the canvas for structures and structures of high complexity. The material is resistant to corrosion, and the polymer coating increases the longevity of operation. The sheet profile differs in profitability, and also resistance to any climate. Without coating, it can be used to make formwork to pour concrete into the foundation. By purchasing C10 corrugated board, the technical characteristics of which motivate consumers to make a choice in its direction, you get the opportunity to reuse the sheet, saving money. The material is easy to install, easy to cut and drill, which makes it easier for the installation crews.
Cost
C10 corrugated board, the price of which will vary depending on the thickness, is supplied with galvanized and polymer coating.
- In the first case, the product of the smallest thickness (4 mm) will cost 196 rubles. per running meter.
- With an increase in thickness to 0.5 mm, the price rises to 229 rubles. for p/m.
- If you are interested in the thickness of 0.55 and 0.7 mm, then you will have to pay 249 and 307 rubles per linear meter of these materials. respectively.
- The price will increase if the corrugated sheet has a polymer coating. This material is presented for sale in several versions - 0.4 mm thick, as well as 0.5 and 0.7 mm thick. In the first case, the cost is 228 rubles. for p/m. For a sheet of 0.5 mm thickness, you will have to pay 268 rubles. And for a linear meter of seven-millimeter corrugated board - 368 rubles
Features of corrugated board application
Corrugated iron can be installed on almost any roof. The distance between the rafters should be equal to the limit from 600 to 900 mm. Between themselves, the sheets are fixed with roofing rivets, and for laying on the roof, roofing screws should be prepared. Holes are pre-drilled for them. If it was not possible to find construction fittings of a suitable shade on sale, then self-tapping screws can be replaced with hex-head screws. You should choose fasteners with a plastic or rubber washer. If you decide to use the latter option, then you must first drill holes at the installation site of the fastener, the diameter of which should be 0.5 mm larger than the screw. It is unacceptable to install corrugated iron on the roof with nails. This technology does not provide for the reason that, under the influence of wind, the nails will not be able to hold the sheet. Self-tapping screws and screws must be installed strictly vertically, which prevents water leakage.
Advice from a sheet strengthening specialist
Sheets of corrugated board are installed on the crate and fixed in places where the wave fits. Approximately 8 fasteners will be needed per square meter. You should try to keep the distance between them the same. To the first and final crate, the sheets are attached to the area of \u200b\u200beach wave, since these sections will have a large wind load. Fastening to intermediate battenscorrugated board is made through the link. At longitudinal joints, the step between fastener elements should not be more than 500 mm.
Important nuances
The corrugated sheet can be laid in one of two existing ways. The first provides for a vertical arrangement of the canvas, while the second - the creation of a block of three sheets. Vertical laying is used for products with a drainage groove. First, the 1st sheet is laid, which is temporarily fixed, after which the first sheet of the 2nd row is located. Next comes the second canvas of the 1st row. Next, install the 2nd sheet of the second row. This will result in a block of 4 canvases, each of which should be aligned and finally fixed.
If you want to strengthen the sheet on the wall, then you should use a metal guide profile for this. First, vertical profiles are installed, which must be fixed to pre-reinforced brackets, then horizontal jumpers should be attached between them. Their location should be convenient. By the time the frame structure is ready, you can start fixing the wall corrugated board, doing this with the help of self-tapping screws.
