As folk wisdom says, the kitchen and bathroom are the face of the hostess. However, maintaining the cleanliness and whiteness of plumbing requires the use of special tools. Store-bought washing gels often cause allergic reactions, have a pungent odor and cost a lot. Alternatively, you can use regular soda, which is in every home. Sodium bicarbonate successfully removes rust and limescale, disinfects the surface and is completely safe for people and pets. In this article, we will tell you some proven ways to clean the bath with baking soda and vinegar, soda ash, and citric acid.
Pros of cleaning the bathroom with baking soda
The main reasons for the refusal of housewives from purchased household chemicals in favor of soda for cleaning plumbing include:
- Efficiency. You can wash the bath with soda and vinegar from rust, waterstone, plaque of cosmetics. Acid and alkali do a good job of killing bacteria, microorganisms and fungi.
- Safety. Bicarbonate does not have a pungent odor, does not cause allergies, and does not leave burns when it comes into contact with the skin.
- Versatility. You can wash the bath with soda and vinegar from any material: enameled, acrylic or steel. The product does not scratch the surface, keeping the coating smooth and shiny.
- Accessibility. Lye and vinegar can be found at any grocery store for a minimal price, and soda ash can be found on the shelf of the hardware store.
How to remove minor dirt
Wash off minor dirt paste of baking soda. A small amount of warm water is added to sodium bicarbonate and stirred until a homogeneous slurry is obtained. Despite the safety of the product, it is better to wear rubber gloves. They will protect the skin of the hands from overdrying with alkali and help preserve the manicure. The surface of the bath is treated with soda paste and left for 60-90 minutes. After the allotted time, use a sponge or brush with soft bristles to clean the surface, and then rinse with water. The temperature of the water doesn't really matter.
Cleaning plumbing fixtures with vinegar
Table vinegar does a good job of removing scale and rust. To wash plumbing from dirt, you need to moisten paper towels with a 9% solution of acetic acid.napkins and cover the surface of the bath with them. The tool will take about three hours to whiten it. After the napkins are removed, and the remaining vinegar is washed off with running water. If the first time it was not possible to completely get rid of yellowness, the procedure can be repeated. This method is great for staining enameled cast iron bathtubs, but care must be taken with acrylic surfaces.
There is another way to remove water scale with vinegar, which has proven to be effective. It is necessary to close the drain hole of the bath and pour a bottle of 9% acetic acid into it. Then it is filled with hot water and left overnight. In the morning, the bath will shine with pristine cleanliness.
How to clean a bathtub with baking soda and vinegar
The state of plumbing largely depends on the quality of water and pipes. Water with a high concentration of sodium and potassium s alts leaves whitish stains on the surface of the bathtub and tiles, the so-called limescale. Poor quality old pipes enrich the water with iron oxides. The latter provokes the appearance of rusty stains on plumbing. Such complex pollution will help wash soda and vinegar in the bath.
Soda ash is a stronger alkali, which is used to soften water, when washing difficult stains, washing dishes. They sell the powder in hardware stores, but making it at home is not difficult. It is necessary to heat sodium bicarbonate for five minutes at a temperature of 150 degrees Celsius. The resulting substance, sodium carbonate, has morelooser consistency than baking soda.
You can wash the bath with soda and vinegar, proceeding as follows: mix baking soda and soda ash in equal parts and add a small amount of water until a homogeneous paste is obtained. The resulting composition should be rubbed on the surface to be cleaned and left for a quarter of an hour. Next, bleach and table vinegar are mixed in equal proportions. The solution is treated with a bath over soda and left for half an hour. After the allotted time, the plumbing is cleaned with a soft brush or sponge, and then washed with running water. This method is able to whiten an old bath and completely remove lime deposits, judging by the reviews. You can also wash the bathtub with soda and vinegar from a rusty coating.
Cleaning plumbing fixtures with citric acid
You can also remove limescale and rust with a lemon. It doesn't smell as strong as vinegar, so people who are sensitive to strong odors can use it freely.
A sachet of acid (100 g) is dissolved in a liter of water, rubbed onto the surface of the bath with a sponge and left for 10 minutes. If the dirt is very strong, you can use wipes soaked in the product and give the acid more time to dissolve the water stone. After the bath is wiped with a sponge and the acid is washed off with water. This method effectively copes with lime deposits, old yellowness and rust stains.
Cleaning the bathtub with baking soda and lemon juice
Do you want to know how to wash the bath with soda and lemon? Very simple! You just need to rubplumbing with soda paste and leave for a quarter of an hour. Then dilute the acid in water at the rate of a tablespoon per half liter of water. The surface of the bath is treated with a solution and the substances are allowed to react for half an hour. The acid dissolves perfectly without the formation of sediment, so it is very convenient to use a spray gun when applying the solution to the surface to be cleaned. After the allotted time, the bath is cleaned with a sponge and the remnants of the product are washed off with water. In such a simple way, it is very easy to wash the bathtub with citric acid from limescale and rust.
Cleaning the bathtub with baking soda and soap
Proved its effectiveness and method of cleaning plumbing with soap. Brown laundry soap should be grated and mixed with laundry soda in equal parts. A little warm water is added to the mixture until a consistency similar to sour cream is formed, and left for 20-30 minutes until the soap swells. 3-5 drops of ammonia are added to the finished paste and the resulting product is applied to the surface of the plumbing. After 60-90 minutes, carefully rubbing the bath with a sponge, the mixture can be washed off. Such a tool helps to get rid of plaque and whiten the surface of even old plumbing.
The use of time-tested folk remedies for cleaning the bathtub allows you to effectively wash plumbing from water stone, rust and plaque. Soda is safe to use, does not cause allergies and has antiseptic properties. Regular use of sodium carbonate,acetic and citric acids for the bathroom will keep it white for many years.
