A very convenient solution is a folding table, with its help you can change the location of the feast, as well as take the design to nature. Such a product will not take up much space in the interior, because when you do not use it, the table can be folded and placed outside the door.
Preparation of tools
A folding table with your own hands can be made by any home craftsman who has de alt with wood at least once in his life. However, to carry out these works, you will need a certain set of tools and materials. You should prepare a screwdriver with a keyless chuck and a set of bits, a manual grinder, a tape measure, a pencil, an electric jigsaw, a building level and a right angle.
If there is no grinder, then it is not necessary to purchase it for one time, it is best to use sandpaper, while you can finish making the table, making its surface smooth. Some modern stores offer consumersuse similar rental equipment.
Preparation of materials
You can make a folding table with your own hands in one evening if you have all the necessary materials at hand. You will need two types of rails, one of them should have a cross section of 30 x 50 mm, while the other should have a cross section of 20 x 40 millimeters. In the first case, you need to prepare four elements, the length of each of which will be 1200 millimeters. The total molding of the latter should be equal to 5 meters.
For the manufacture of countertops, you can use glued solid wood, which is made of pine. A reliable and durable option will be a countertop, the thickness of which varies from 30 to 40 millimeters. A part is cut out of the workpiece with the following dimensions: 1300 x 650 millimeters. Each component is well processed with sandpaper, and then varnished, which should be done even before the assembly of the structure. The slats that will form the basis of the legs must be rounded in the upper part, and then sanded well.
Additional preparation of elements
A folding table with your own hands is made in sizes that will suit the future owner. But the technology remains the same as described in the article. Thus, in the legs, which have not yet been sawn to length, it is necessary to drill through holes, they will be needed for the frame strips and axle bolts. The diameter for fasteners should be 8 millimeters, and for the straps, the two holes should have a diameter of 5 millimeters.
In the centralparts of the bar should be drilled a hole for the axle bolts, stepping back from above 430 millimeters. Frame strips are marked by eye, but symmetry should be observed.
Nuances of the work
A do-it-yourself folding table is made according to a certain technology, it provides for the creation of goats and countertops, these components should not be fastened together. In the countertop, it is necessary to make grooves where they will be installed, and then the legs will be wedged. Special sockets must be made in such a way that they are fastened to the table top with 4 x 50 mm self-tapping screws.
At the next stage, you can proceed to the assembly of the structure. If you decide to make a folding table with your own hands, then the goats should look like a clamshell, such a system will save space in the house or in the trunk of your car.
Initially, the legs should not be sawn off from the bottom, but they should be approximately the same. The axle bolts are also not tightened to the end, so that it is possible to expand the legs. To secure the tolerance, locknuts should be used. The master can purchase absolutely any bolts, however, their length and diameter must be suitable. For legs, for example, 8 x 70 mm bolts should be used. Limiting bolts should be used in the grooves of the tabletop, the parameters of which are 8 x 120 millimeters.
Expert Tips
When constructeda folding picnic table with your own hands, in the next step, you can install the upper ends of the legs in the unfolded state into the grooves of the table top. The unfinished structure should be placed on any flat surface to determine how much the legs need to be cut off to eliminate length errors. In this case, be sure to use the building level. When adjusting the length, you should not be particularly zealous; to carry out these manipulations, you will need a jigsaw. If the table will be used only in nature, then the generally accepted height of 750 millimeters should be reduced, since you will literally have to sit at such a design on the ground.
Making a folding coffee table
You can also make a folding coffee table with your own hands, its photos are presented in the article. The frame is assembled for confirmations, and you need to use a special drill. Marking on the surface of the chipboard can be done with the help of stickers, since the pencil will not be visible, its lines glare. A transformation mechanism should be installed in the frame, which has the shape of a rectangle, but before that, springs are mounted to help unfold the structure. The mechanism is fixed in a through way, because the weight of the table will be impressive.
Folding legs should hide all technical fasteners and holes. Marking for fasteners can be done in the same way. Through holes for the bolts should be prepared in the next step, then the drill indicates the place for installing the headbolt. This fastener will allow you to fix the mechanism, but do not be afraid that the number of fasteners is large enough. The legs look like a rectangle and should be as strong as possible, since the weight of the entire structure is approximately 45 kilograms. Between themselves, these components should be fixed with ties.
A folding table with your own hands, the drawings of which are presented in the article, can be completed by you in one evening. The next step is to screw the legs to the structure itself, for this, the fasteners are initially marked. You can drill in place if you have enough experience. Installation is recommended to be carried out on metal bushings. For this fastener, holes are drilled in the legs. Legs are installed on four sides, which will allow you to hide the technical holes in the frame.
Assembling the table top
The tabletop must be assembled with extreme precision, as the hinged unfolding is strong enough to ensure that the elements slide smoothly. It will be quite difficult to keep the hinge in the sockets, and the screws cannot cope with this task. Therefore, other hinges can be purchased. The tabletop of this design is divided into two parts, first a small one is installed, then a large one. At this point, we can assume that the table is ready for use.
Recommendations for making a universal design
DIY folding picnic table,the drawings of which are presented in the article, can be made according to individual sizes. You can make the design according to the principle of a book-table, which has an attractive appearance. To do this, you need to prepare two legs, a drawstring, underframe, 4 horizontal and two vertical beams, a movable leg and piano hinges. All cuts must first be edged. After the central part is fastened. The next step is to assemble the tabletop and fix the cover to the ends of the legs. The movable element with the frame is installed on the piano hinges, only after that the table can be assembled completely, and, if necessary, varnished.
Conclusion
When a do-it-yourself folding camping table or any other type of design for eating is being made, the preparation of the details is especially difficult. It is better to entrust their sawing to professionals if you do not have special skills and tools. But each master will be able to do the assembly on his own.
