In everyday life, there is often such a problem as a broken door handle. This situation gives people a clear inconvenience - without it it is difficult to open the door leaf. Door handle repair is a rare occurrence. This is explained by the fact that few people know how to properly fix breakdowns in the mechanism. Proper door handle repair depends entirely on the design of the lock.
What types of pens are there?
It is important to remember what types of pens exist. Having correctly determined which group the broken handle belongs to, it becomes easy to understand the cause of the breakdown and eliminate it. Distinguish:
- Rotary structures. They are presented in the form of large door handles. In order for the mechanism to start its work, the knob must be turned clockwise (in some cases counterclockwise).
- Press. The main difference between this element and all the others is the presence of a lever. When you press it, the tongue goes down. Repair of this type of door handle is easy, without additionalacquisitions.
What breaks most often on the front door handle?
The front door is usually equipped with one of two types of handles. Distinguish pressure, with a latch, and also stationary. The first open the lock when you press the handle. Stationary mechanical help to open the door. They usually have only mechanical failures. Such mechanisms are most often not repaired. Buy a new pen and replace the old one. They are designed as one piece.
A variety of breakdowns can be found in lever handles. The four most common types of damage are:
- The handle itself falls off, and the fasteners remain in the door. Such a breakdown indicates a low quality product. It is simply replaced with a new one.
- The inner square breaks in the doorknob, which just bursts. After that, the latch cannot be opened. This problem is explained by the fact that manufacturers use a material such as silumin in their work. This material is not durable, it often breaks under excessive loads.
- When the latch wears out over time, it may not open. A situation is possible when the outer square sinks. Such a breakdown is reflected in the latch mechanism, because it is this square that plays the role of a handle connector on both sides. This part wears out very rarely. If the square was released with a marriage, then it may break. The defect can be seen, since the square will move to one of the handles, and the second one will simply stop opening the latch. Such a breakdown is noticed immediately. It turns out that on the one hand the handle works, but on the other hand the door does not open. In this case, it is better not to postpone the repair of the door handle.
- The handle should return to its original position after being pressed, but in some cases this does not happen. There is a breakdown. Most often, the coil spring bursts. It can also move to the side. Repairing a defect of this kind is quite simple, but it will take some time.
What do you need for disassembly?
Repairing a doorknob always starts with a process of taking it apart piece by piece. If all the necessary tools are available, then removing it is quite easy. When a person knows the algorithm of actions, he will spend no more than five minutes. You need to follow the sequence of steps:
- It is necessary to unscrew the screw, which is located at the bottom of the handle. You should not unscrew this element to the end, it may be lost due to its small size.
- The main grip fasteners are usually hidden under a decorative trim. You need to remove this cover. You need to turn it counterclockwise. No tools are needed for this job, the part is easy to unscrew by hand.
- After removing the trim, you can see the mounting system of the handle. Usually it consists of self-tapping screws. There are cases when the system is fastened with screw ties. You can unscrew the fasteners with a screwdriver, which is at hand.
- The next step is to remove the handle from the desired square.
How do I remove the handle that is presented as a large pad?
It happens that handles are placed on the front doors, which look like a large overlay on the door. To remove such an element, you must do the following:
- There are screws along the edges of the door lining. They must be unscrewed with a screwdriver. The handle should come off with the trim. If you unscrew the screws on one side of the door, the handle will be removed from each side.
- When the old part is removed, you can start installing the new one.
Removing the handle is a fairly easy process. If you follow the instructions step by step, then there should be no problems.
Installing a new handle is also a simple process. It is necessary to perform all the steps to remove the door handle, only in reverse order. An important nuance in this case is the choice of a similar product.
How to repair the handle on the front door?
Repair should begin with finding out the breakdown. Often there is such a situation when the handle disappears, and its base is still in the door. In this case, most likely, the retaining ring was damaged or fell out of the lock. It is easy to put it in place with some effort. Repair of the front door handle is carried out in the following order:
- It is necessary to remove the handle from the front door, which is still on it. The snap ring should also be on the door leaf. If it is not damaged, then you need to connectelements of the handle and put the ring in its original place. After carrying out such actions, you need to put the handle in place. Often the retaining ring breaks, then the question arises of acquiring a new locking element. This decision is made when the ring is bent. It happens that it bursts.
- It happens that the square that is inside the handle bursts. This occurs when manufacturers save on this element, making it from fragile material. When it burst under the influence of loads, it will have to be definitely changed. When buying a new accessory, you should pay attention to steel handles for front doors. We can say that the repair of the door handle of a metal door is carried out by analogy with the usual one. First check the square. It is necessary to find out whether it is in working condition or not.
- Some people happen that the latch does not close when the handle is working. Usually such a defect in the operation of the mechanism appears if the square moves to the side. In this case, the square was made short. One of the handles needs to be removed. Fits any door handle. Then pull out a short square. The removed element is replaced by a new one. It is important to put everything in its place after the replacement is completed.
The new square can be found at the local market. Usually they sell long models that need to be adjusted to the required size. You can do this sort of thing yourself. To do this, you need a grinder. If there is no such tool, then you will have to work with a hacksaw.
What should I do if the handle does not return to its original position?
Repair of the front door handle is required when it does not reach its original position when the door is closed. The reason most often lies in a broken coil spring. It is repaired by analogy with the retaining ring. It is necessary to remove the handle, replace the spring. The spring is usually fixed with a special washer. In turn, the retaining ring secures the washer. On the market, as well as in specialized stores, it is difficult to find this item for sale. Therefore, most often you have to buy a new pen and put it in place of the old one.
Repair Tips
Repair of the door handle of the entrance metal door is carried out by analogy with the fittings of interior doors. Breakdowns are mostly the same. The main thing in this case is to understand the cause of the breakdown. It is possible to find out which element of the door handle is out of order only after parsing the handle. Almost anyone who has the skills to work with tools can repair the element.
The main point is the removal of the handle from the mounts. It is important to know how this device works. It is necessary to find out which of the elements performs any specific function. After the design itself becomes clear, it will be clear how to carry out repairs.
Latch handles
Repair of the interior door handle is required quite often in everyday life. At some point, the mechanism fails. This happens if the latch handle is used for a long period of time.time. Many people think that this kind of mechanism cannot be repaired, but it is not.
Latch door handle repair is a standard procedure for people living in apartments. It is important to start repairs at the first manifestations of a breakdown. Then there is a chance that you will not have to change the handle entirely. It happens that the latch sticks. The movement of the crossbars is limited when the door closes, the same thing happens when you try to open the door. Frequent breakage is the immobility of the tongue. When a person presses the interior handle, the mechanism does not come into action. The tongue begins to fall periodically, it becomes more and more difficult to get it out.
Conclusion
So, we found out how different types of door handles are repaired. As you can see, the operation is not too complicated. In extreme cases, the entire element can be replaced.
